Manuals / Genie / Lawn and Garden / Utility Vehicle

Genie Z-45, Z-25J manual Maintenance Check the Engine Oil Level, Maintenance Symbols Legend

Models: Z-45, Z-25J Z-45, Z-25

1 59

Download 59 pages 37.07 Kb

Page 51

Maintenance Symbols Legend

Fourth Edition · First Printing	Operator's Manual

Observe and Obey:

Only routine maintenance items specified in this manual shall be performed by the operator.

Scheduled maintenance inspections shall be completed by qualified service technicians, according to the manufacturer's specifications and the requirements specified in the responsibilities manual.

Use only Genie approved replacement parts.

Maintenance Symbols Legend

The following symbols have been used in this manual to help communicate the intent of the instructions. When one or more of the symbols appear at the beginning of a maintenance procedure, it conveys the meaning below.

Indicates that tools will be required to perform this procedure.

Indicates that new parts will be required to perform this procedure.

Indicates that a cold engine is required before performing this procedure.

Maintenance

Check the Engine Oil Level

Maintaining the proper engine oil level is essential to good engine performance and service life. Operating the machine with an improper oil level can damage engine components.

Note: Check the oil level with the engine off.

1Remove the safety pin from the engine pivot plate latch.

The engine pivot plate latch is located under the engine turntable pivot plate at the counterweight end of the machine.

2Open the engine pivot plate latch and swing the engine pivot plate out and away from the machine.

3Check the oil dipstick. Add oil as needed.

4Swing the engine back to its original position and close the engine pivot plate latch.

5Install the engine pivot plate safety pin.

Perkins 404C-22 Engine

Oil type	15W-40

Oil type - cold conditions	5W-40

Ford DSG-423 EFI Engine (EPA Compliant)

Oil type	5W-20

Deutz F3L 2011 Engine

Oil type	15W-40

Oil type - cold conditions	5W-30

Part No.114339

Z-45/25 • Z-45/25J

49

Image 51

Genie Z-45, Z-25J manual Maintenance Check the Engine Oil Level, Maintenance Symbols Legend, Observe and Obey

Contents

Z-4525 Z-4525J IC PowerAustralia with Maintenance Information Operator’s ManualContact us Contents1 Avoid hazardous situations Owners, Users and OperatorsIntroduction Danger Do Not Operate UnlessSafety Sign Maintenance Introduction Hazard ClassificationIntended Use Symbol and Hazard Pictorials Definitions Operators Manual Symbol and Hazard Pictorials DefinitionsSafety signs and locations General SafetyFourth Edition · First Printing General SafetySafety signs and locations Operators ManualOperators Manual General SafetySafety signs and locations Fourth Edition · First PrintingFourth Edition · First Printing General SafetySafety signs and locations Operators ManualOperators Manual General SafetySafety signs and locations Fourth Edition · First PrintingFourth Edition · First Printing General SafetySafety signs and locations Operators ManualPersonal Safety Fall Protection Tip-overHazards Work Area Safety Electrocution HazardsWork Area Safety Operators Manual Work Area SafetyWork Area Safety Operation on Slopes Hazards Fall Hazards Collision HazardsWork Area Safety Component Damage Hazards Work Area Safety Explosion and Fire HazardsBodily Injury Hazard Damaged Machine HazardsLockout After Each Use Work Area Safety Battery Safety Burn HazardsExplosion Hazard Electrocution HazardLegend Platform Control Panel ControlsFourth Edition · First Printing ControlsControls Operators ManualPlatform Control Panel Fourth Edition · First Printing ControlsControls Ground Control PanelControls Fourth Edition · First PrintingGround Control Panel Operators Manual ControlsInspections Pre-operationInspection Fundamentals 2Always perform a pre-operationinspectionDo Not Operate Unless Inspections Pre-operationInspection Inspections Function Test Fundamentals 3Always perform function tests prior to useDo Not Operate Unless Test the Machine Functions InspectionsAt the Ground Controls Test Emergency StopTest Machine Functions Test the Foot SwitchAt the Platform Controls Test the HornTest the Drive Enable System Test Drive and BrakingInspections Test Limited Drive Speed - Standard Base Models Test Limited Drive Speed - Narrow Base ModelsInspections Test Auxiliary Controls Test the Lift/Drive Select Function if equippedTest Aircraft Protection Package if equipped InspectionsDo Not Operate Unless FundamentalsInspections Workplace Inspection 4Inspect the workplaceQuantity Inspections Inspection for Decals with WordsPart No Decal DescriptionOperators Manual Inspections Ground Controls Side DriveChassis Platform Engine Side Fourth Edition · First PrintingQuantity Inspections Inspection for Decals with SymbolsPart No Decal DescriptionOperators Manual Inspections Ground Controls Side DriveChassis Platform Engine Side Fourth Edition · First PrintingOperating Instructions Do Not Operate Unless 5Only use the machine as it was intendedFundamentals Auxiliary Controls Starting the EngineOperating Instructions Emergency StopTo Steer Operating Instructions Operation from GroundOperation from Platform To Position PlatformOperating Instructions run riseDriving on a slope To determine the slope gradeDrive Speed Select Machine Not Level Indicator Light if equippedDrive Enable Generator if equippedOperating Instructions Check Engine Light if equippedAircraft Protection Package if equipped After Each UseFree-wheelConfiguration for Winching Transport and Lifting InstructionsObserve and Obey Securing the Platform - Z-45/25J Securing to Truck or Trailer for TransitSecuring the Platform - Z-45/25 Securing the ChassisTransport and Lifting Instructions Lifting InstructionsY Axis X AxisMaintenance Check the Engine Oil Level Maintenance Symbols LegendObserve and Obey Maintenance Check the Hydraulic Oil Level Maintenance Check the BatteriesCheck the Tire Pressure Maintenance Scheduled Maintenance Maximum slope rating, stowed position, 2WD SpecificationsStandard Base Models Z-45/25no jibMaximum slope rating, stowed position, 2WD SpecificationsStandard Base Models Z-45/25JjibMaximum slope rating, stowed position SpecificationsNarrow Base Models Z-45/25no jibMaximum slope rating, stowed position SpecificationsNarrow Base Models Z-45/25JjibPart No.114339 SpecificationsFourth Edition · First Printing Operators Manual