Initial Set Up | Graco Inc GX-7 400, 311321H, GX-7 DI, GX-7A

Initial Set Up

1.Install female quick disconnect fitting to air supply hose bundled with chemical supply hoses.

2.Connect coupling block to hose bundle. Connect A-Isocyanate hose (red-tape) to notched fitting on coupling block. Connect R-Resin hose (blue-tape) to fitting without notches on coupling block.

3.Close both manual valves.

4.Pressurize A and R chemical hoses. Check for leaks. See Proportioner manual.

Operation Basics

5.Bleed air from chemical hoses.

a.Use separate waste containers for A-ISO and R-Resin.

b.Hold coupling block with exit ports pointed into waste container.

c.Open one manual valve at a time to dis- pense into waste container.

d.Bleed each side until chemical leaving hoses is free of air.

e.Close both manual valves.

6.Use cloth soaked in gun cleaner to clean coupling block and mating surfaces.

7.Set safety stop to CLOSED (SERVICE).

8.Install coupling block to gun.

9.Proceed with daily start-up and shutdown procedures.

311321H

17

Image 17

Graco Inc GX-7 400, 311321H, GX-7 DI, GX-7A important safety instructions Initial Set Up

Contents

GX-7 Important Safety Instructions311321H Models Contents Personal Protective Equipment Fire and Explosion Hazard Pressurized Aluminum Parts Hazard Model GX-7 DI Overall ViewModel GX-7A Locknut Model GX-7Valving Rod Rear Stop Gun Block Air Cap Valve Trigger GX-7A Centerline Components Centerline Components GX-7 400 Centerline Components GX-7A Mixing Module Mixing Module Operation Basics Safety PositionIsocyanate Hazard Keep a and B Components Separate Air Hose Connection Disengage Safety StopConnect Air Hoses Disconnect Air Hoses Manual Valves Installation and RemovalCoupling Block Remove Coupling Block Air Inlet ConfigurationOptional Configuration Do not Overtighten Mixing Module and PCD Installation GX-7 DI Model Only Valving Rod AdjustmentGX-7A and GX-7 400 Models Only Initial Set Up Daily Shutdown Daily Start-up Trigger Gun Pressure Relief Procedure Clean Spray Gun Procedure MaintenanceGun Service Kits Flush Gun Remove Centerline Components Service Screen ScrewRepair Remove valving rod. Rod Draw Bar Valving Rod Install Centerline Components GX-7 DI Shown Replace End Cap and Air Piston Assembly Replace Trigger Valve O-Ring Replace Trigger Valve O-Rings Unthread Cap from PCD Body Clean Mixing Module Install Mixing Module Install Mixing Module GX-7A Model Shown Clean Pattern Control Disc Parts GX-7A Model Final Assembly Module see GX-7A Mix Mod GX-7A Model Final AssemblyNo. Part No. Description GX-7 DI Model Final Assembly No. Part No. Description Qty GX-7 DI Model Final AssemblyModule see GX-7 DI Model Specifications , GX-7 400 Model Final Assembly Module Kit , GX-7 400 Model Final Assembly GX-7A Model Handle Assembly Description GX-7 Model Handle Assembly GX-7 DI Model Handle Assembly Description Qty GX-7 DI Model Handle Assembly GX-7 400 Model Handle Assembly GX-7 400 Model Handle Assembly All models Coupling Block Assembly GX-7A Mix Module Kit Specifications Tip Set-Up Chart for GX-7A Model GX-7 400 Mix Module Kit Module Kits Cleanout Drill Iso PortQuantity In/mm Module Only Size Ref Tip Kits for GX-7 400 Gun No. Ref Quantity Set-up Chart for GX-7 400 Model Module/Tip Data for Chemical Sprayed at 2500 PSI Output GX-7 DI Model SpecificationsPattern Lbs/min Round Spray Pattern Tool Kits Tip KitsFor GX-7A and GX-7 DI Models Round Tip Kits Size Quantity Category Data Technical Data Graco Standard Warranty