GX-7 DI Model Specifications, Pattern Lbs/min | Graco Inc GX-7A

Specifications

GX-7 DI Model Specifications

Module/Tip Data for Chemical Sprayed at 2500 PSI

				❄Output
✖ Module Kit	Cleanout Drill	Ref. No.	❄Pattern	(lbs/min)

		Fan Spray Pattern


296900 (#2)	246625	212	12 in. wide	12

	(.086 diameter)	206	20 in. wide	22
		213	12 in. wide	12

		204	20 in. wide	21

296901 (#4)	248892	212	10 in. wide	8

	(.028 diameter)	206	24 in. wide	11
		204	18 in. wide	10

296903 (#5)	246816	212	11 in. wide	4

	(.018 diameter)	213	12 in. wide	4
		208	8 in. wide	4

Round Spray Pattern

296903 (#5)

246816

(.018 diameter)

40	4 in. diameter	8
55	7 in. diameter	9.5

70	8 in. diameter	9.75

90	10 in. diameter	9.75

❄Actual results may vary due to chemical system characteristics, temperature, pressure, and ratio.

✖Includes appropriate cleanout drills.

Mix Module Kit

Part No.	Size Ref.	Quantity

296898	PEEK 018/018	1

296899	PEEK 028/028	1

Module Only

Part No.	Size Ref.

296902	#5

311321H

47

Image 47

Graco Inc GX-7A GX-7 DI Model Specifications, Module/Tip Data for Chemical Sprayed at 2500 PSI Output, Pattern Lbs/min

Contents

GX-7 Important Safety Instructions311321H Models Contents Personal Protective Equipment Fire and Explosion Hazard Pressurized Aluminum Parts Hazard Model GX-7 DI Overall ViewModel GX-7A Trigger Model GX-7Locknut Valving Rod Rear Stop Gun Block Air Cap Valve GX-7A Centerline Components Centerline Components GX-7 400 Centerline Components GX-7A Mixing Module Mixing Module Keep a and B Components Separate Safety PositionOperation Basics Isocyanate Hazard Disconnect Air Hoses Disengage Safety StopAir Hose Connection Connect Air Hoses Manual Valves Installation and RemovalCoupling Block Remove Coupling Block Air Inlet ConfigurationOptional Configuration Do not Overtighten Mixing Module and PCD Installation GX-7 DI Model Only Valving Rod AdjustmentGX-7A and GX-7 400 Models Only Initial Set Up Daily Shutdown Daily Start-up Trigger Gun Pressure Relief Procedure Clean Spray Gun Procedure MaintenanceGun Service Kits Flush Gun Remove Centerline Components Service Screen ScrewRepair Remove valving rod. Rod Draw Bar Valving Rod Install Centerline Components GX-7 DI Shown Replace End Cap and Air Piston Assembly Replace Trigger Valve O-Ring Replace Trigger Valve O-Rings Unthread Cap from PCD Body Clean Mixing Module Install Mixing Module Install Mixing Module GX-7A Model Shown Clean Pattern Control Disc Parts GX-7A Model Final Assembly Module see GX-7A Mix Mod GX-7A Model Final AssemblyNo. Part No. Description GX-7 DI Model Final Assembly No. Part No. Description Qty GX-7 DI Model Final AssemblyModule see GX-7 DI Model Specifications , GX-7 400 Model Final Assembly Module Kit , GX-7 400 Model Final Assembly GX-7A Model Handle Assembly Description GX-7 Model Handle Assembly GX-7 DI Model Handle Assembly Description Qty GX-7 DI Model Handle Assembly GX-7 400 Model Handle Assembly GX-7 400 Model Handle Assembly All models Coupling Block Assembly GX-7A Mix Module Kit Specifications Tip Set-Up Chart for GX-7A Model Module Only Size Ref Module Kits Cleanout Drill Iso PortGX-7 400 Mix Module Kit Quantity In/mm Tip Kits for GX-7 400 Gun No. Ref Quantity Set-up Chart for GX-7 400 Model Round Spray Pattern GX-7 DI Model SpecificationsModule/Tip Data for Chemical Sprayed at 2500 PSI Output Pattern Lbs/min Round Tip Kits Size Quantity Tip KitsTool Kits For GX-7A and GX-7 DI Models Category Data Technical Data Graco Standard Warranty