GX-7 DI Model Final Assembly | Graco Inc GX-7 400, 311321H, GX-7A

Parts

GX-7 DI Model Final Assembly (295541)

Ref.
No. Part No. Description			Qty.
1	295809	Spray gun handle assembly	1
2	15B772	Air hose, 1/4 in. x 23 in. (FXF)	1
3	295596	Coupler plug	1
4	295597	Coupler	1
5	295835	R-screen screw	1
6	296792	Screen, 80 mesh (pack of 10)	-
	296724	Screen, 80 mesh (pack of 50)	-
7	296713	Check valve assembly	2
		(pack of 2)
8	295860	Gun block	1
9		Module; see GX-7 DI Model	1
		Specifications, page 47
10	295837	Module retainer	1
11		Tip; see Tip Kits, page 48	1
12	296865	Tip retainer	1
13	295838	Air cap	1
14	296128	Coupling block gasket	-
		(pack of 2)
15	295433	Coupling block mounting screw	1
	296979	Coupling block mounting screw	-
		(pack of 2)
16	295834	A-screen screw	1
17	295836	Rear seal gland	1
18	296864	Rear seal retainer assembly	1
19	296829	Rear seal packing (pack of 5)	-
20	295383	Coupling block (not shown)	1
21	100030	Fitting	1

311321H

33

Image 33

Graco Inc GX-7 400 GX-7 DI Model Final Assembly, No. Part No. Description Qty, Module see GX-7 DI Model Specifications

Contents

Important Safety Instructions 311321HGX-7 Models Contents Personal Protective Equipment Fire and Explosion Hazard Pressurized Aluminum Parts Hazard Overall View Model GX-7AModel GX-7 DI Locknut Model GX-7Valving Rod Rear Stop Gun Block Air Cap Valve Trigger GX-7A Centerline Components Centerline Components GX-7 400 Centerline Components GX-7A Mixing Module Mixing Module Operation Basics Safety PositionIsocyanate Hazard Keep a and B Components Separate Air Hose Connection Disengage Safety StopConnect Air Hoses Disconnect Air Hoses Installation and Removal Coupling BlockManual Valves Air Inlet Configuration Optional ConfigurationRemove Coupling Block Do not Overtighten Mixing Module and PCD Installation Valving Rod Adjustment GX-7A and GX-7 400 Models OnlyGX-7 DI Model Only Initial Set Up Daily Shutdown Daily Start-up Trigger Gun Pressure Relief Procedure Maintenance Gun Service KitsClean Spray Gun Procedure Flush Gun Service Screen Screw RepairRemove Centerline Components Remove valving rod. Rod Draw Bar Valving Rod Install Centerline Components GX-7 DI Shown Replace End Cap and Air Piston Assembly Replace Trigger Valve O-Ring Replace Trigger Valve O-Rings Unthread Cap from PCD Body Clean Mixing Module Install Mixing Module Install Mixing Module GX-7A Model Shown Clean Pattern Control Disc Parts GX-7A Model Final Assembly GX-7A Model Final Assembly No. Part No. DescriptionModule see GX-7A Mix Mod GX-7 DI Model Final Assembly GX-7 DI Model Final Assembly Module see GX-7 DI Model Specifications ,No. Part No. Description Qty GX-7 400 Model Final Assembly Module Kit , GX-7 400 Model Final Assembly GX-7A Model Handle Assembly Description GX-7 Model Handle Assembly GX-7 DI Model Handle Assembly Description Qty GX-7 DI Model Handle Assembly GX-7 400 Model Handle Assembly GX-7 400 Model Handle Assembly All models Coupling Block Assembly GX-7A Mix Module Kit Specifications Tip Set-Up Chart for GX-7A Model GX-7 400 Mix Module Kit Module Kits Cleanout Drill Iso PortQuantity In/mm Module Only Size Ref Tip Kits for GX-7 400 Gun No. Ref Quantity Set-up Chart for GX-7 400 Model Module/Tip Data for Chemical Sprayed at 2500 PSI Output GX-7 DI Model SpecificationsPattern Lbs/min Round Spray Pattern Tool Kits Tip KitsFor GX-7A and GX-7 DI Models Round Tip Kits Size Quantity Category Data Technical Data Graco Standard Warranty