GX-7 400 Model Final Assembly, Module Kit | Graco Inc GX-7A manual

Parts

GX-7 400 Model Final Assembly (295540)

Ref.
No. Part No. Description			Qty.
1	15B772	Air hose	1
2	296128	Coupling block gasket	-
		(pack of 2)
3	295596	Coupler plug	1
4	295597	Coupler	1
5	295384	Gun block (includes 13)	1
6	296722	Check valve assembly	-
		(pack of 10)
7	295799	Spray gun handle assembly	1
8	296692	Valving rod	2
9	296792	Screen-80, mesh (pack of 10)	-
	296724	Screen-80, mesh (pack of 50)	-
10		A-Screen screw	1
11		R-Screen screw	1
12	296693	Screen screw seal (pack of 2)	-
	296723	Screen screw seal (pack of 10)	-
13	295433	Coupling block mounting screw	1
	296979	Coupling block mounting screw	-
		kit (pack of 2)
14	296828	Rear packing retainer	1
15	296829	Rear seal packing	1
		(pack of 5)
16	296830	Rear seal retainer	1
18		Module; see GX-7 400 Mix	1
		Module Kit, page 45
19	296836	Retainer	1
20	296837	Air cap	1
21		Tip; see Tip Kits, page 48	1
22	296833	A-gun block screen screw	-
		assembly
		(includes 6, 9, 10, 12)
23	296834	R-gun block screen screw	-
		assembly
		(includes 6, 9, 10, 12)
24	100030	Fitting	1

311321H

35

Image 35

Graco Inc GX-7A, 311321H, GX-7 DI important safety instructions GX-7 400 Model Final Assembly, Module Kit

Contents

GX-7 Important Safety Instructions311321H Models Contents Personal Protective Equipment Fire and Explosion Hazard Pressurized Aluminum Parts Hazard Model GX-7 DI Overall ViewModel GX-7A Trigger Model GX-7Locknut Valving Rod Rear Stop Gun Block Air Cap Valve GX-7A Centerline Components Centerline Components GX-7 400 Centerline Components GX-7A Mixing Module Mixing Module Keep a and B Components Separate Safety PositionOperation Basics Isocyanate Hazard Disconnect Air Hoses Disengage Safety StopAir Hose Connection Connect Air Hoses Manual Valves Installation and RemovalCoupling Block Remove Coupling Block Air Inlet ConfigurationOptional Configuration Do not Overtighten Mixing Module and PCD Installation GX-7 DI Model Only Valving Rod AdjustmentGX-7A and GX-7 400 Models Only Initial Set Up Daily Shutdown Daily Start-up Trigger Gun Pressure Relief Procedure Clean Spray Gun Procedure MaintenanceGun Service Kits Flush Gun Remove Centerline Components Service Screen ScrewRepair Remove valving rod. Rod Draw Bar Valving Rod Install Centerline Components GX-7 DI Shown Replace End Cap and Air Piston Assembly Replace Trigger Valve O-Ring Replace Trigger Valve O-Rings Unthread Cap from PCD Body Clean Mixing Module Install Mixing Module Install Mixing Module GX-7A Model Shown Clean Pattern Control Disc Parts GX-7A Model Final Assembly Module see GX-7A Mix Mod GX-7A Model Final AssemblyNo. Part No. Description GX-7 DI Model Final Assembly No. Part No. Description Qty GX-7 DI Model Final AssemblyModule see GX-7 DI Model Specifications , GX-7 400 Model Final Assembly Module Kit , GX-7 400 Model Final Assembly GX-7A Model Handle Assembly Description GX-7 Model Handle Assembly GX-7 DI Model Handle Assembly Description Qty GX-7 DI Model Handle Assembly GX-7 400 Model Handle Assembly GX-7 400 Model Handle Assembly All models Coupling Block Assembly GX-7A Mix Module Kit Specifications Tip Set-Up Chart for GX-7A Model Module Only Size Ref Module Kits Cleanout Drill Iso PortGX-7 400 Mix Module Kit Quantity In/mm Tip Kits for GX-7 400 Gun No. Ref Quantity Set-up Chart for GX-7 400 Model Round Spray Pattern GX-7 DI Model SpecificationsModule/Tip Data for Chemical Sprayed at 2500 PSI Output Pattern Lbs/min Round Tip Kits Size Quantity Tip KitsTool Kits For GX-7A and GX-7 DI Models Category Data Technical Data Graco Standard Warranty