Manuals / Omega Speaker Systems / Household Appliance / Home Security System

Omega Speaker Systems iSE-TC BATTERY & S5 JUMPER LOCATION RELAY CONNECTOR, I/O Contact, Connector

Models: iSE-TC

1 60

Download 60 pages 10.72 Kb

Page 12

Image 12

2.4 Disassembly Instruction

You will need to open the unit for one of the following reasons:

•To wire relay and I/O contact connectors. (Refer to Section 2.6).

•To connect or replace the battery. (Refer to Section 2.7).

•To change S5 jumper. In the absence of AC power, and if S5 is installed, the LCD Backlight and iSE board will be on and running on the battery power. (Refer to Section 2.7).

Disconnect the power supply before proceeding. Remove cover by removing 2 screws on each side.

BATTERY &

S5 JUMPER

LOCATION

RELAY

CONNECTOR

I/O CONTACT
CONNECTOR	ETHERNET &
THERMOCOUPLE	ETHERNET &
CONNECTORS	DC POWER
	CONNECTORS

COVER

FLASH

CARD

MOUNTING

SCREWS (2)

TRAY

Figure 2.5 Opening the Unit

Page 12

Image 12

Omega Speaker Systems iSE-TC BATTERY & S5 JUMPER LOCATION RELAY CONNECTOR, I/O Contact, Connector, Ethernet, Thermocouple

Contents

Shop on line at User’s GuideDual Thermocouple over the Internet For Latest Product ManualsPage Part 1 Introduction LIST OF FIGURES LIST OF TABLESFigure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure FigureFEATURES PART INTRODUCTION EMC Considerations1.2 Before You Begin 1.3 DescriptionLOCAL ALARMS --The iSE includes two 1.5 Amp output relays that are controlled by the alarm conditions you select. The relays can trigger flashing lights and a siren for example to alert personnel near the scene Page Figure 2.1 Mounting Figure 2.2 Dimensions PART 2 HARDWARE 2.1 Wall Mounting2.2 DIP Switches Figure 2.3 DIP Switch LocationRESET DIAGNOSTICS2.3 Parts of the iSE Unit Figure 2.4 Parts of the iSE UnitBATTERY & S5 JUMPER LOCATION RELAY CONNECTOR CONNECTORCONNECTORS CONNECTORS2.5.2 10Base-TCrossover Wiring 2.6 Relay and I/O Contact Wiring ConnectionsCrossover Cable Wiring 2.7 DC Power Input Wiring Connections2.8 Running on Battery Power Figure 2.9 Battery and S5 Jumper Location9VDC BATTERY INSULATOR COVER S5 PINSFigure 2.10Chart of Simulated Data 2.9 Flash Memory FormatDATA RECORD TEST PART NETWORK CONFIGURATION 3.1 Network Protocols 3.2 Ethernet MAC AddressFigure 3.1 Labeling Figure 3.2 DIP Switch on the Bottom Side of iSE OFF4 3 2 ON3.3 DHCP 3.4 DNS3.5.1 Default IP Address Figure 3.3 Telnet Login into the iSE3.6 Port Number Example C \ Telnet4.0 Testing the Connection PART OPERATIONSFigure 4.1 Pinging the iSE from MS-DOSPrompt 4.1 iConnect Software iSERVER HOME PAGE Figure 4.3 Accessing the iSE’s Home Page Menu4.1 iConnect Software continued ACCESS CONTROL 4.2 Setting a New IP Address over the NetworkFigure 4.4 Access Control LOGIN ADMINISTRATOR4.3Setup and Operation Using the iSE Web Page prompted for a password, as shown in FigureEngineering TemperatureTemperature Output SignalAccessing iSE units within your internal network Accessing iSE units using the internetDiagnostics 4.3.1.3 Browser Proxy Selection4.3.2 Adjustable Chart Figure 4.8 Adjustable Chart4.3.3 Retrieving Data from Flash OPTIONOPTION 4.3.4 Access Control 4.3.4 Access Control continued 4.3.5 Configuration#1 RTC is not set and Flash Card is empty #2 RTC is set, and recording is in progressCONFIGURATION Flash Recording SettingsRemote Access Tunneling Figure 4.11 Configuration4.3.5 Configuration continued A Configuration/Device SetupTemperature 1and Temperature B Real Time ClockF Flash Recording 4.3.5 Configuration continued Start Recording Select to initiate a recording4.3.5 Configuration continued G Input Contact ClosureH Terminal Server 4.3.5 Configuration continued I Remote Access Figure 4.12 Sensor Parameters - Temperature 4.3.6 Sensor ParametersFigure 4.13 Sensor Parameters - Input Contact 4.3.6 Sensor Parameters continued TA71.34F TA72.48F TD-1.19FTA71.34FTA72.48FTD-1.19F 4.4 Telnet Setup 4.5 HTTPget Program4.5.1 HTTPget using Port httpget -r -S“*SRTC\r” 4.5.1 HTTPget using Port 1000 continuedare parameters needed for the command string is the command as the following4.5.2 HTTPget and ARP to setup Device IP Address arp -s192.168.1.200 00-03-34-00-06-b6where Figure 4.15 ARP Commands and Responses 4.6 ARP Protocol4.7 iLog Software Figure 4.16 iLog Software Logging DataFile Monitor Mail View Help Status Indicators Data Email ErrorDev1 alarm Dev2 alarm Dev1 alarm Dev1 alarm Dev2 alarm Dev1 alarm Dev1 alarmOptions Alarm Editor CancelHelp Range AccuracyPt / 13%Rh-Pt 50to 40C / 40 to 1768CiSE SPECIFICATIONS LED IndicatorsAlarm I/O’s POWERPART FACTORY PRESET VALUES PRESET PARAMETERSFACTORY DEFAULTS Remote Access TunnelingSupply power. Unit measures Temperature The ac/dc power adaptor is 9VdcPART APPROVALS INFORMATIONAPPENDIX AGLOSSARY Appendix BIP Address Appendix CIP Netmask Address ClassMask Binary Value Mask Decimal ValueASCII Chart Appendix DBinary ASCIIASCII Chart Continuation Appendix DASCII Hex Ctrl KeyiLog Error Messages Error #Appendix E DescriptionPage Page WARRANTY/DISCLAIMER RETURN REQUESTS/INQUIRIESTRADEMARK NOTICE OMEGA…Of Course

2.4 Disassembly Instruction

BATTERY &

I/O CONTACT

CONNECTOR

ETHERNET &

THERMOCOUPLE

CONNECTORS

DC POWER

COVER

Figure 2.5 Opening the Unit