DIP Switches, DIP Switch Location | Omega Speaker Systems iSE-TC

2.2 DIP Switches

The iSE is shipped with all DIP switches in "OFF" position.

DIP Switch Usage

1) N/C - not used

2) To change to default factory settings

3) To enable/disable DHCP

4) N/C - not used

Figure 2.3 DIP Switch Location

To set the iSE to factory default settings, slide DIP switch #2 to ON position. Power the iSE on and wait about 10 seconds until the iSE fully boots up. Set the DIP switch #2 back to OFF position (it does not matter if the iSE is powered ON or OFF, just make sure that the DIP switch is set to OFF, otherwise, every time the unit is power-cycled the factory settings will take over.

To enable the DHCP, besides using DIP switch #3, set the iSE’s IP address to 0.0.0.0. An iSE with IP address of 0.0.0.0 will request an IP address, gateway address, and subnet mask from the DHCP server over the Ethernet

6

Image 10

Omega Speaker Systems iSE-TC manual DIP Switches, DIP Switch Location

Contents

User’s Guide Page Dhcp DNS List of Figures ISE and iLD Big Display on the Ethernet Network Features Part Introduction Page ISE and iLD Big Display on the Ethernet Network Part 2 Hardware Wall Mounting DIP Switches DIP Switch Location Parts of the iSE Unit Parts of iSE Unit Disassembly Instruction Opening the Unit Crossover Cable Wiring Relay and I/O Contact Wiring ConnectionsNetwork Communication Interfaces 1 10Base-T RJ-45 Pinout Running on Battery Power Battery and S5 Jumper Location Flash Memory Format Data Record Test Part Network Configuration 3.1 Network ProtocolsEthernet MAC Address Subnet Mask DhcpDNS Section Port Number Default IP AddressExample C\Telnet 192.168.1.200 Testing the Connection Part Operations IConnect Software ISERVER Home Setting a New IP Address over the Network Access Control Prompted for a password, as shown in Figure Setup and Operation Using the iSE WebLogin and Administrator Passwords Read Sensor Java Runtime Environment 1.4 Setup instructions Read Sensor Accessing iSE units using the internet Java Runtime Environment 1.5 5.0 Setup instructionsDiagnostics Adjustable Chart Fla sh Archive Retrieving Data from Flash Option Dhcp can be enabled by setting the dip switch number #2 RTC is set, and recording is in progress Configuration#1 RTC is not set and Flash Card is empty #4 RTC is not set and the Flash Card is not empty Real Time Clock Flash Recording SettingsRemote Access Tunneling MegaBytes Flash Card 22 Kbytes Used Space Configuration/Device Setup Temperature 1 and Temperature Input 2 Status Unlatch, Latch, Clear Latch, Chart SP Flash Recording Configuration Configuration Input Contact Closure Terminal Server Configuration Remote Access 12 Sensor Parameters Temperature Sensor Parameters TA71.34F TA72.48F TD-1.19F TA71.34FTA72.48FTD-1.19F Telnet Setup HTTPget Program HTTPget using Port Srhc SrtcSrtf Srhf Arp -s 192.168.1.200 00-03-34-00-06-b6 HTTPget and ARP to setup Device IP AddressWhere 15 ARP Commands and Responses ARP Protocol ILog Software 16 iLog Software Logging Data Installation Mail Notifier Software Email Setup Options Device Setting and Configuration Device setup requires 19 iSE Mail Notifier Device Setting Part Specifications Sensor Specifications Thermocouple Input Environmental PowerInterfaces Packaging Network Interface Part Approvals Information CE Approval Measurement Category Appendix Aglossary Appendix BIP Address Or Dotted Notation Appendix CIP NetmaskAddress Class Mask Binary Value Mask Decimal Value Mask Dotted Notation Mask Binary Mask Bits Dec Binary Appendix D Hex Ascii Chart Dec BinaryAscii Char No Parity No parity Dec Hex Ctrl Key Ascii Control Codes Definition Appendix D Ascii Chart ContinuationChar Equiv Appendix E ILog Error Messages Error # Description Page Page WARRANTY/DISCLAIMER Shop on line at omega.com