Manuals / Omega Speaker Systems / Household Appliance / Home Security System

Omega Speaker Systems iSE-TC Flash Memory Format, Data Record Test, 10Chart of Simulated Data

Models: iSE-TC

1 60

Download 60 pages 10.72 Kb

Page 15

2.9 Flash Memory Format

2.9 Flash Memory Format

A 2 Meg flash memory card is included with your product. This memory card is already formatted; however, the following procedure describes how to format your memory card. Once the memory card is formatted, all the data that had previously been

recorded will be replaced by simulated test data (see Figure 2.10).

1) Unplug the AC adaptor from the unit.

2) Hold down the ºC/ºF button and connect the AC adaptor back into the unit. Release the ºC/ºF button.

3) You will see the following message appear on the LCD: *ºWAITº* *FLASH*.

4) Wait for about 60 seconds and a new message should appear: *ºWAITº* *OKAY*.

5) Press the ºC/ºF button once and this message will appear: DATA-RECORD-TEST.

6) Press the TIME button and this message will appear: DATA RECORD TEST -

DATA RECORD TEST.

8) Again, press the ºC/ºF button, the firmware version will appear, followed by *OKAY*.

9) Unplug the AC adaptor and plug it back in. The flash memory card is now formatted. To verify whether the formatting was completed correctly, you should be able to see the following graph on the WEB server’s “Chart” page.

Figure 2.10 Chart of Simulated Data

11

Image 15

Omega Speaker Systems iSE-TC manual Flash Memory Format, Data Record Test, 10Chart of Simulated Data

Contents

For Latest Product Manuals Shop on line atUser’s Guide Dual Thermocouple over the InternetPage Part 1 Introduction Figure Figure Figure Figure Figure Figure Figure LIST OF FIGURESLIST OF TABLES Figure Figure Figure Figure Figure Figure FigureFEATURES 1.3 Description PART INTRODUCTIONEMC Considerations 1.2 Before You BeginLOCAL ALARMS --The iSE includes two 1.5 Amp output relays that are controlled by the alarm conditions you select. The relays can trigger flashing lights and a siren for example to alert personnel near the scene Page PART 2 HARDWARE 2.1 Wall Mounting Figure 2.1 Mounting Figure 2.2 DimensionsFigure 2.3 DIP Switch Location 2.2 DIP SwitchesFigure 2.4 Parts of the iSE Unit RESETDIAGNOSTICS 2.3 Parts of the iSE UnitCONNECTORS BATTERY & S5 JUMPER LOCATION RELAY CONNECTORCONNECTOR CONNECTORS2.7 DC Power Input Wiring Connections 2.5.2 10Base-TCrossover Wiring2.6 Relay and I/O Contact Wiring Connections Crossover Cable WiringS5 PINS 2.8 Running on Battery PowerFigure 2.9 Battery and S5 Jumper Location 9VDC BATTERY INSULATOR COVERFigure 2.10Chart of Simulated Data 2.9 Flash Memory FormatDATA RECORD TEST PART NETWORK CONFIGURATION 3.1 Network Protocols 3.2 Ethernet MAC AddressFigure 3.1 Labeling 3.4 DNS Figure 3.2 DIP Switch on the Bottom Side of iSEOFF4 3 2 ON 3.3 DHCPExample C \ Telnet 3.5.1 Default IP AddressFigure 3.3 Telnet Login into the iSE 3.6 Port Number4.0 Testing the Connection PART OPERATIONSFigure 4.1 Pinging the iSE from MS-DOSPrompt 4.1 iConnect Software iSERVER HOME PAGE Figure 4.3 Accessing the iSE’s Home Page Menu4.1 iConnect Software continued ACCESS CONTROL 4.2 Setting a New IP Address over the NetworkFigure 4.4 Access Control prompted for a password, as shown in Figure LOGINADMINISTRATOR 4.3Setup and Operation Using the iSE Web PageOutput Signal EngineeringTemperature Temperature4.3.1.3 Browser Proxy Selection Accessing iSE units within your internal networkAccessing iSE units using the internet DiagnosticsFigure 4.8 Adjustable Chart 4.3.2 Adjustable Chart4.3.3 Retrieving Data from Flash OPTIONOPTION 4.3.4 Access Control #2 RTC is set, and recording is in progress 4.3.4 Access Control continued4.3.5 Configuration #1 RTC is not set and Flash Card is emptyFigure 4.11 Configuration CONFIGURATIONFlash Recording Settings Remote Access TunnelingB Real Time Clock 4.3.5 Configuration continuedA Configuration/Device Setup Temperature 1and TemperatureF Flash Recording Start Recording Select to initiate a recording 4.3.5 Configuration continued4.3.5 Configuration continued G Input Contact ClosureH Terminal Server 4.3.5 Configuration continued I Remote Access Figure 4.12 Sensor Parameters - Temperature 4.3.6 Sensor ParametersFigure 4.13 Sensor Parameters - Input Contact 4.3.6 Sensor Parameters continued TA71.34F TA72.48F TD-1.19FTA71.34FTA72.48FTD-1.19F 4.5 HTTPget Program 4.4 Telnet Setup4.5.1 HTTPget using Port is the command as the following httpget -r -S“*SRTC\r”4.5.1 HTTPget using Port 1000 continued are parameters needed for the command string4.5.2 HTTPget and ARP to setup Device IP Address arp -s192.168.1.200 00-03-34-00-06-b6where 4.6 ARP Protocol Figure 4.15 ARP Commands and ResponsesFigure 4.16 iLog Software Logging Data 4.7 iLog SoftwareDev2 alarm Dev1 alarm Dev1 alarm File Monitor Mail View Help Status IndicatorsData Email Error Dev1 alarm Dev2 alarm Dev1 alarm Dev1 alarmOptions Alarm Editor CancelHelp 50to 40C / 40 to 1768C RangeAccuracy Pt / 13%Rh-PtPOWER iSE SPECIFICATIONSLED Indicators Alarm I/O’sRemote Access Tunneling PART FACTORY PRESET VALUESPRESET PARAMETERS FACTORY DEFAULTSAPPROVALS INFORMATION Supply power. Unit measures TemperatureThe ac/dc power adaptor is 9Vdc PARTAPPENDIX AGLOSSARY Appendix BIP Address Mask Decimal Value Appendix CIP NetmaskAddress Class Mask Binary ValueASCII ASCII ChartAppendix D BinaryHex Ctrl Key ASCII Chart ContinuationAppendix D ASCIIDescription iLog Error MessagesError # Appendix EPage Page WARRANTY/DISCLAIMER RETURN REQUESTS/INQUIRIESTRADEMARK NOTICE OMEGA…Of Course