Manuals / Omega Speaker Systems / Household Appliance / Home Security System

Omega Speaker Systems iSE-TC 4 Parts of the iSE Unit, 1 Parts of iSE Unit, Ethernet, Reset

Models: iSE-TC

1 60

Page 11

2.3 Parts of the iSE Unit

		Figure 2.4 Parts of the iSE Unit
		Figure 2.4 Parts of the iSE Unit
Table 2.1 Parts of iSE Unit
ETHERNET		RJ45 interface for 10BASE-T connection.
ETHERNET		RJ45 interface for 10BASE-T connection.
RESET		Button: Used for power reseting the iSE.
ACTIVITY		LED (Red) Blinking: Indicates network activities (receiving or sending packets).
NET LINK		LED (Green) Solid: Indicates good network link.
DIAGNOSTICS		LED (Yellow) Blinking: Indicates transmitting data from iSE to flash memory
		card. When DHCP enabled, it remains solid until DHCP IP address is received.
°C/°F		LED (Green) Blinking: Indicates receiving data by the iSE from flash memory.
°C/°F		Button: Change display units of measurement from °C to °F
TIME		Button: Change display from DATE and TIME to TEMP
BKLT		Button: Display Back Light
When using the		small push buttons, hold the button until “WAIT” is displayed on the LCD and
When using the
then release.	7
	7

Page 11

Image 11

Omega Speaker Systems iSE-TC 4 Parts of the iSE Unit, 1 Parts of iSE Unit, Ethernet, Reset, Activity, Net Link, Time

Contents

For Latest Product Manuals Shop on line atUser’s Guide Dual Thermocouple over the InternetPage Part 1 Introduction Figure Figure Figure Figure Figure Figure Figure LIST OF FIGURESLIST OF TABLES Figure Figure Figure Figure Figure Figure FigureFEATURES 1.3 Description PART INTRODUCTIONEMC Considerations 1.2 Before You BeginLOCAL ALARMS --The iSE includes two 1.5 Amp output relays that are controlled by the alarm conditions you select. The relays can trigger flashing lights and a siren for example to alert personnel near the scene Page PART 2 HARDWARE 2.1 Wall Mounting Figure 2.1 Mounting Figure 2.2 DimensionsFigure 2.3 DIP Switch Location 2.2 DIP SwitchesFigure 2.4 Parts of the iSE Unit RESETDIAGNOSTICS 2.3 Parts of the iSE UnitCONNECTORS BATTERY & S5 JUMPER LOCATION RELAY CONNECTORCONNECTOR CONNECTORS2.7 DC Power Input Wiring Connections 2.5.2 10Base-TCrossover Wiring2.6 Relay and I/O Contact Wiring Connections Crossover Cable WiringS5 PINS 2.8 Running on Battery PowerFigure 2.9 Battery and S5 Jumper Location 9VDC BATTERY INSULATOR COVERDATA RECORD TEST Figure 2.10Chart of Simulated Data2.9 Flash Memory Format Figure 3.1 Labeling PART NETWORK CONFIGURATION 3.1 Network Protocols3.2 Ethernet MAC Address 3.4 DNS Figure 3.2 DIP Switch on the Bottom Side of iSEOFF4 3 2 ON 3.3 DHCPExample C \ Telnet 3.5.1 Default IP AddressFigure 3.3 Telnet Login into the iSE 3.6 Port NumberFigure 4.1 Pinging the iSE from MS-DOSPrompt 4.0 Testing the ConnectionPART OPERATIONS 4.1 iConnect Software 4.1 iConnect Software continued iSERVER HOME PAGEFigure 4.3 Accessing the iSE’s Home Page Menu Figure 4.4 Access Control ACCESS CONTROL4.2 Setting a New IP Address over the Network prompted for a password, as shown in Figure LOGINADMINISTRATOR 4.3Setup and Operation Using the iSE Web PageOutput Signal EngineeringTemperature Temperature4.3.1.3 Browser Proxy Selection Accessing iSE units within your internal networkAccessing iSE units using the internet DiagnosticsFigure 4.8 Adjustable Chart 4.3.2 Adjustable ChartOPTION 4.3.3 Retrieving Data from FlashOPTION 4.3.4 Access Control #2 RTC is set, and recording is in progress 4.3.4 Access Control continued4.3.5 Configuration #1 RTC is not set and Flash Card is emptyFigure 4.11 Configuration CONFIGURATIONFlash Recording Settings Remote Access TunnelingB Real Time Clock 4.3.5 Configuration continuedA Configuration/Device Setup Temperature 1and TemperatureF Flash Recording Start Recording Select to initiate a recording 4.3.5 Configuration continuedH Terminal Server 4.3.5 Configuration continuedG Input Contact Closure 4.3.5 Configuration continued I Remote Access Figure 4.13 Sensor Parameters - Input Contact Figure 4.12 Sensor Parameters - Temperature4.3.6 Sensor Parameters TA71.34FTA72.48FTD-1.19F 4.3.6 Sensor Parameters continuedTA71.34F TA72.48F TD-1.19F 4.5 HTTPget Program 4.4 Telnet Setup4.5.1 HTTPget using Port is the command as the following httpget -r -S“*SRTC\r”4.5.1 HTTPget using Port 1000 continued are parameters needed for the command stringwhere 4.5.2 HTTPget and ARP to setup Device IP Addressarp -s192.168.1.200 00-03-34-00-06-b6 4.6 ARP Protocol Figure 4.15 ARP Commands and ResponsesFigure 4.16 iLog Software Logging Data 4.7 iLog SoftwareDev2 alarm Dev1 alarm Dev1 alarm File Monitor Mail View Help Status IndicatorsData Email Error Dev1 alarm Dev2 alarm Dev1 alarm Dev1 alarmOptions Help Alarm EditorCancel 50to 40C / 40 to 1768C RangeAccuracy Pt / 13%Rh-PtPOWER iSE SPECIFICATIONSLED Indicators Alarm I/O’sRemote Access Tunneling PART FACTORY PRESET VALUESPRESET PARAMETERS FACTORY DEFAULTSAPPROVALS INFORMATION Supply power. Unit measures TemperatureThe ac/dc power adaptor is 9Vdc PARTAPPENDIX AGLOSSARY Appendix BIP Address Mask Decimal Value Appendix CIP NetmaskAddress Class Mask Binary ValueASCII ASCII ChartAppendix D BinaryHex Ctrl Key ASCII Chart ContinuationAppendix D ASCIIDescription iLog Error MessagesError # Appendix EPage Page TRADEMARK NOTICE WARRANTY/DISCLAIMERRETURN REQUESTS/INQUIRIES OMEGA…Of Course

2.3 Parts of the iSE Unit

Figure 2.4 Parts of the iSE Unit

Table 2.1 Parts of iSE Unit

ETHERNET

RESET

ACTIVITY

NET LINK

DIAGNOSTICS

TIME

BKLT