Manuals / Omega Speaker Systems / Household Appliance / Home Security System

Omega Speaker Systems iSE-TC manual Alarm Editor, Cancel, Help

Models: iSE-TC

1 60

Download 60 pages 10.72 Kb

Page 46

Alarm Editor

4.8.3 Device Setting and Configuration Device setup requires:

• Server IP Address: for iSE device (for example 192.168.1.200).

• Socket Number: (1000 or 2000 depending on iSE settings).

• Bus Address/Device ID: interface address (1 to 199). Enter "0" for RS232 interface or for iSE.

• Reading Cmd: normally set to SRFT to obtain reading from the devices. If you want to change this setting, refer to list of commands in Section 4.5.

• Alarm Type: (High/Low, High value, or Low value).

• Info Message: text can be entered to describe the alarm condition.

• Email Interval: the time interval in which the email is sent.

• Monitor Interval: the interval or time resolution in which readings will be obtained from the device.

• Alarm Hold Time: the time delay of each subsequential alarm notification to be sent.

Alarm Editor

Device Info	(1 of 2)							OK
Server IP Address		192.168.1.200						OK
Server IP Address		192.168.1.200
Socket Number			1000				Cancel
Bus Address/Device ID			1					Help
Description				Dev 2
Src ID				Dev 2			Add	Del
Reading Cmd							Only Monitor Access
			zRdgA				Only Monitor Access
			zRdgA
			SRTF				to iServer device
Alarm Configuration							to iServer device
Alarm Configuration
Alarm Type	Alarm High			Info Message
Alarm High	73			Email Interval			0.05	hrs.
Alarm Low	0			Monitor Interval			0.5	min.
				Alarm Hold Time			0.0	min.

Figure 4.19 iSE Mail Notifier Device Setting

42

Image 46

Omega Speaker Systems iSE-TC manual Alarm Editor, Cancel, Help

Contents

Dual Thermocouple over the Internet Shop on line atUser’s Guide For Latest Product ManualsPage Part 1 Introduction Figure Figure Figure Figure Figure Figure Figure LIST OF FIGURESLIST OF TABLES Figure Figure Figure Figure Figure Figure FigureFEATURES 1.2 Before You Begin PART INTRODUCTIONEMC Considerations 1.3 DescriptionLOCAL ALARMS --The iSE includes two 1.5 Amp output relays that are controlled by the alarm conditions you select. The relays can trigger flashing lights and a siren for example to alert personnel near the scene Page Figure 2.1 Mounting Figure 2.2 Dimensions PART 2 HARDWARE 2.1 Wall Mounting2.2 DIP Switches Figure 2.3 DIP Switch Location2.3 Parts of the iSE Unit RESETDIAGNOSTICS Figure 2.4 Parts of the iSE UnitCONNECTORS BATTERY & S5 JUMPER LOCATION RELAY CONNECTORCONNECTOR CONNECTORSCrossover Cable Wiring 2.5.2 10Base-TCrossover Wiring2.6 Relay and I/O Contact Wiring Connections 2.7 DC Power Input Wiring Connections9VDC BATTERY INSULATOR COVER 2.8 Running on Battery PowerFigure 2.9 Battery and S5 Jumper Location S5 PINS2.9 Flash Memory Format Figure 2.10Chart of Simulated DataDATA RECORD TEST 3.2 Ethernet MAC Address PART NETWORK CONFIGURATION 3.1 Network ProtocolsFigure 3.1 Labeling 3.3 DHCP Figure 3.2 DIP Switch on the Bottom Side of iSEOFF4 3 2 ON 3.4 DNS3.6 Port Number 3.5.1 Default IP AddressFigure 3.3 Telnet Login into the iSE Example C \ TelnetPART OPERATIONS 4.0 Testing the ConnectionFigure 4.1 Pinging the iSE from MS-DOSPrompt 4.1 iConnect Software Figure 4.3 Accessing the iSE’s Home Page Menu iSERVER HOME PAGE4.1 iConnect Software continued 4.2 Setting a New IP Address over the Network ACCESS CONTROLFigure 4.4 Access Control 4.3Setup and Operation Using the iSE Web Page LOGINADMINISTRATOR prompted for a password, as shown in FigureTemperature EngineeringTemperature Output SignalDiagnostics Accessing iSE units within your internal networkAccessing iSE units using the internet 4.3.1.3 Browser Proxy Selection4.3.2 Adjustable Chart Figure 4.8 Adjustable ChartOPTION 4.3.3 Retrieving Data from FlashOPTION 4.3.4 Access Control #1 RTC is not set and Flash Card is empty 4.3.4 Access Control continued4.3.5 Configuration #2 RTC is set, and recording is in progressRemote Access Tunneling CONFIGURATIONFlash Recording Settings Figure 4.11 ConfigurationTemperature 1and Temperature 4.3.5 Configuration continuedA Configuration/Device Setup B Real Time ClockF Flash Recording 4.3.5 Configuration continued Start Recording Select to initiate a recordingG Input Contact Closure 4.3.5 Configuration continuedH Terminal Server 4.3.5 Configuration continued I Remote Access 4.3.6 Sensor Parameters Figure 4.12 Sensor Parameters - TemperatureFigure 4.13 Sensor Parameters - Input Contact TA71.34F TA72.48F TD-1.19F 4.3.6 Sensor Parameters continuedTA71.34FTA72.48FTD-1.19F 4.4 Telnet Setup 4.5 HTTPget Program4.5.1 HTTPget using Port are parameters needed for the command string httpget -r -S“*SRTC\r”4.5.1 HTTPget using Port 1000 continued is the command as the followingarp -s192.168.1.200 00-03-34-00-06-b6 4.5.2 HTTPget and ARP to setup Device IP Addresswhere Figure 4.15 ARP Commands and Responses 4.6 ARP Protocol4.7 iLog Software Figure 4.16 iLog Software Logging DataDev1 alarm Dev2 alarm Dev1 alarm Dev1 alarm File Monitor Mail View Help Status IndicatorsData Email Error Dev2 alarm Dev1 alarm Dev1 alarmOptions Cancel Alarm EditorHelp Pt / 13%Rh-Pt RangeAccuracy 50to 40C / 40 to 1768CAlarm I/O’s iSE SPECIFICATIONSLED Indicators POWERFACTORY DEFAULTS PART FACTORY PRESET VALUESPRESET PARAMETERS Remote Access TunnelingPART Supply power. Unit measures TemperatureThe ac/dc power adaptor is 9Vdc APPROVALS INFORMATIONAPPENDIX AGLOSSARY Appendix BIP Address Mask Binary Value Appendix CIP NetmaskAddress Class Mask Decimal ValueBinary ASCII ChartAppendix D ASCIIASCII ASCII Chart ContinuationAppendix D Hex Ctrl KeyAppendix E iLog Error MessagesError # DescriptionPage Page RETURN REQUESTS/INQUIRIES WARRANTY/DISCLAIMERTRADEMARK NOTICE OMEGA…Of Course