Manuals / Omega Speaker Systems / Household Appliance / Home Security System

Omega Speaker Systems iSE-TC manual HTTPget and ARP to setup Device IP Address, where

Models: iSE-TC

1 60

Download 60 pages 10.72 Kb

Page 41

Image 41

4.5.2 HTTPget and ARP to setup Device IP Address

Use the iConnect software, which may be downloaded from our website, to do these IP changes whenever possible.

Use ARP first to assign the mac address to a static IP address in computer arp table by this command:

arp –s 192.168.1.200 00-03-34-00-06-b6

Then use the following command to assign new IP to the device: httpget –r–S "00000000" 192.168.1.200:1

where:

“00000000” is admin. password. If the password is wrong, the unit will ignore the new IP. If the new IP is taken, you will get the message " New IP is Assigned" after the HTTPget command. The device will reset automatically. (TX and RX led is on for 2 seconds).

“192.168.1.200” is an example of an IP adress. It is replaced with an IP address suitable for your network

“00-03-34-00-06-b6” is replaced with your iSE product MAC address.

Page 41

Image 41

Omega Speaker Systems iSE-TC HTTPget and ARP to setup Device IP Address, arp -s192.168.1.200 00-03-34-00-06-b6, where

Contents

User’s Guide Shop on line atDual Thermocouple over the Internet For Latest Product ManualsPage Part 1 Introduction LIST OF TABLES LIST OF FIGURESFigure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure FigureFEATURES EMC Considerations PART INTRODUCTION1.2 Before You Begin 1.3 DescriptionLOCAL ALARMS --The iSE includes two 1.5 Amp output relays that are controlled by the alarm conditions you select. The relays can trigger flashing lights and a siren for example to alert personnel near the scene Page PART 2 HARDWARE 2.1 Wall Mounting Figure 2.1 Mounting Figure 2.2 DimensionsFigure 2.3 DIP Switch Location 2.2 DIP SwitchesDIAGNOSTICS RESET2.3 Parts of the iSE Unit Figure 2.4 Parts of the iSE UnitCONNECTOR BATTERY & S5 JUMPER LOCATION RELAY CONNECTORCONNECTORS CONNECTORS2.6 Relay and I/O Contact Wiring Connections 2.5.2 10Base-TCrossover WiringCrossover Cable Wiring 2.7 DC Power Input Wiring ConnectionsFigure 2.9 Battery and S5 Jumper Location 2.8 Running on Battery Power9VDC BATTERY INSULATOR COVER S5 PINSDATA RECORD TEST Figure 2.10Chart of Simulated Data2.9 Flash Memory Format Figure 3.1 Labeling PART NETWORK CONFIGURATION 3.1 Network Protocols3.2 Ethernet MAC Address OFF4 3 2 ON Figure 3.2 DIP Switch on the Bottom Side of iSE3.3 DHCP 3.4 DNSFigure 3.3 Telnet Login into the iSE 3.5.1 Default IP Address3.6 Port Number Example C \ TelnetFigure 4.1 Pinging the iSE from MS-DOSPrompt 4.0 Testing the ConnectionPART OPERATIONS 4.1 iConnect Software 4.1 iConnect Software continued iSERVER HOME PAGEFigure 4.3 Accessing the iSE’s Home Page Menu Figure 4.4 Access Control ACCESS CONTROL4.2 Setting a New IP Address over the Network ADMINISTRATOR LOGIN4.3Setup and Operation Using the iSE Web Page prompted for a password, as shown in FigureOutput Signal EngineeringTemperature 76.37Accessing iSE units using the internet Accessing iSE units within your internal networkDiagnostics 4.3.1.3 Browser Proxy SelectionFigure 4.8 Adjustable Chart 4.3.2 Adjustable ChartOPTION 4.3.3 Retrieving Data from FlashOPTION 4.3.4 Access Control 4.3.5 Configuration 4.3.4 Access Control continued#1 RTC is not set and Flash Card is empty #2 RTC is set, and recording is in progressFlash Recording Settings CONFIGURATIONRemote Access Tunneling Figure 4.11 ConfigurationA Configuration/Device Setup 4.3.5 Configuration continuedB Real Time Clock Temperature 1and TemperatureF Flash Recording Start Recording Select to initiate a recording 4.3.5 Configuration continuedH Terminal Server 4.3.5 Configuration continuedG Input Contact Closure 4.3.5 Configuration continued I Remote Access Figure 4.13 Sensor Parameters - Input Contact 4.3.6 Sensor ParametersFigure 4.12 Sensor Parameters - Temperature TA71.34FTA72.48FTD-1.19F 4.3.6 Sensor Parameters continuedTA71.34F TA72.48F TD-1.19F 4.5 HTTPget Program 4.4 Telnet Setup4.5.1 HTTPget using Port 4.5.1 HTTPget using Port 1000 continued httpget -r -S“*SRTC\r”are parameters needed for the command string is the command as the followingwhere 4.5.2 HTTPget and ARP to setup Device IP Addressarp -s192.168.1.200 00-03-34-00-06-b6 4.6 ARP Protocol Figure 4.15 ARP Commands and ResponsesFigure 4.16 iLog Software Logging Data 4.7 iLog SoftwareData Email Error File Monitor Mail View Help Status IndicatorsDev1 alarm Dev2 alarm Dev1 alarm Dev1 alarm Dev2 alarm Dev1 alarm Dev1 alarmOptions Help Alarm EditorCancel Accuracy RangePt / 13%Rh-Pt 50to 40C / 40 to 1768CLED Indicators iSE SPECIFICATIONSAlarm I/O’s POWERPRESET PARAMETERS PART FACTORY PRESET VALUESFACTORY DEFAULTS Remote Access TunnelingThe ac/dc power adaptor is 9Vdc Supply power. Unit measures TemperaturePART APPROVALS INFORMATIONAPPENDIX AGLOSSARY Appendix BIP Address Address Class Appendix CIP NetmaskMask Binary Value Mask Decimal ValueAppendix D ASCII ChartBinary ASCIIAppendix D ASCII Chart ContinuationASCII Hex Ctrl KeyError # iLog Error MessagesAppendix E DescriptionPage Page TRADEMARK NOTICE WARRANTY/DISCLAIMERRETURN REQUESTS/INQUIRIES OMEGA…Of Course