Manuals / Graco Inc / Power Tools / Paint Sprayer

Graco Inc 311321H, GX-7 400, GX-7 DI Air Hose Connection, Disengage Safety Stop, Connect Air Hoses

Models: GX-7A 311321H GX-7 DI GX-7 400

1 50

Download 50 pages 51.4 Kb

Page 12

Operation Basics

Disengage Safety Stop

To disengage safety stop, push in and turn safety stop counterclockwise to place gun in OPEN position (red band is exposed).

Red Band

OPEN

Red band exposed when spraying.

FIG. 11: Safety Stop - Open

Air Hose Connection

Connect Air Hoses

Pull back sleeve of female fitting, insert male fitting and slide sleeve forward to secure con- nection.

Disconnect Air Hoses

Pull back sleeve of female fitting and pull out male fitting.

Pull Sleeve

Close Manual Valves

Closing manual valves prevents chemicals in heated hoses from entering gun. For your own

safety, close manuals valves before servicing FIG. 13: Disconnect Air Hose gun.

Manual Valves -

rotate clockwise to

close.

FIG. 12: Close Manual Valves

12

311321H

Image 12

Graco Inc 311321H Air Hose Connection, Disengage Safety Stop, Connect Air Hoses, Disconnect Air Hoses, Close Manual Valves

Contents

Important Safety Instructions 311321HGX-7 Contents ModelsPersonal Protective Equipment Fire and Explosion Hazard Pressurized Aluminum Parts Hazard Overall View Model GX-7AModel GX-7 DI Model GX-7 LocknutValving Rod Rear Stop Gun Block Air Cap Valve TriggerCenterline Components GX-7A Centerline ComponentsGX-7 400 Centerline Components Mixing Module GX-7A Mixing ModuleSafety Position Operation BasicsIsocyanate Hazard Keep a and B Components SeparateDisengage Safety Stop Air Hose ConnectionConnect Air Hoses Disconnect Air HosesInstallation and Removal Coupling BlockManual Valves Air Inlet Configuration Optional ConfigurationRemove Coupling Block Mixing Module and PCD Installation Do not OvertightenValving Rod Adjustment GX-7A and GX-7 400 Models OnlyGX-7 DI Model Only Initial Set Up Daily Start-up Daily ShutdownPressure Relief Procedure Trigger GunMaintenance Gun Service KitsClean Spray Gun Procedure Flush Gun Service Screen Screw RepairRemove Centerline Components Remove valving rod. Rod Draw Bar Valving Rod Install Centerline Components Replace End Cap and Air Piston Assembly GX-7 DI ShownReplace Trigger Valve O-Rings Replace Trigger Valve O-RingClean Mixing Module Unthread Cap from PCD BodyInstall Mixing Module Install Mixing ModuleClean Pattern Control Disc GX-7A Model ShownGX-7A Model Final Assembly PartsGX-7A Model Final Assembly No. Part No. DescriptionModule see GX-7A Mix Mod GX-7 DI Model Final Assembly GX-7 DI Model Final Assembly Module see GX-7 DI Model Specifications ,No. Part No. Description Qty GX-7 400 Model Final Assembly GX-7 400 Model Final Assembly Module Kit ,GX-7A Model Handle Assembly GX-7 Model Handle Assembly DescriptionGX-7 DI Model Handle Assembly GX-7 DI Model Handle Assembly Description QtyGX-7 400 Model Handle Assembly GX-7 400 Model Handle Assembly Coupling Block Assembly All modelsSpecifications GX-7A Mix Module KitSet-Up Chart for GX-7A Model TipModule Kits Cleanout Drill Iso Port GX-7 400 Mix Module KitQuantity In/mm Module Only Size RefSet-up Chart for GX-7 400 Model Tip Kits for GX-7 400 Gun No. Ref QuantityGX-7 DI Model Specifications Module/Tip Data for Chemical Sprayed at 2500 PSI OutputPattern Lbs/min Round Spray PatternTip Kits Tool KitsFor GX-7A and GX-7 DI Models Round Tip Kits Size QuantityTechnical Data Category DataGraco Standard Warranty