Technical Data, Category Data | Graco Inc GX-7 400, 311321H, GX-7 DI

Technical Data

Technical Data

Category	Data
Air Supply	100-125 psi (7.9 bars)
Maximum Operating Pressure	3500 psi (24 MPa, 240 bar)
Maximum Output ❄	GX-7A Model:
	40 lbs/min (18 kg/min)
	GX-7 DI Model:
	22 lbs/min (10 kg/min)
	GX-7 400 Model:
	8 lbs/min (3.6 kg/min)
Minimum Output ❄	GX-7A Model:
	4 lbs/min (1.8 kg/min)
	GX-7 DI Model:
	4 lbs/min (1.8 kg/min)
	GX-7 400 Model:
	3.5 lbs/min (1.6 kg/min)
Height	9 in. (23 cm)
Length	9.5 in. (24 cm)
Width	4.5 in. (11 cm)
Weight	3.5 lbs. (1.5 kg)
Mixing	GX-7A Model:
	Internal impingement, airless atomization,
	solvent-free, mechanically self cleaning
	GX-7 DI Model:
	Internal direct impingement, airless atomiza-
	tion, solvent-free, mechanically self cleaning
	GX-7 400 Model:
	Internal direct impingement, airless atomiza-
	tion, solvent-free, mechanically self cleaning

❄Theoretical: actual results will vary with operating conditions

311321H

49

Image 49

Graco Inc GX-7 400, 311321H, GX-7 DI, GX-7A important safety instructions Technical Data, Category Data

Contents

311321H Important Safety InstructionsGX-7 Models Contents Personal Protective Equipment Fire and Explosion Hazard Pressurized Aluminum Parts Hazard Model GX-7A Overall ViewModel GX-7 DI Locknut Model GX-7Valving Rod Rear Stop Gun Block Air Cap Valve Trigger GX-7A Centerline Components Centerline Components GX-7 400 Centerline Components GX-7A Mixing Module Mixing Module Operation Basics Safety PositionIsocyanate Hazard Keep a and B Components Separate Air Hose Connection Disengage Safety StopConnect Air Hoses Disconnect Air Hoses Coupling Block Installation and RemovalManual Valves Optional Configuration Air Inlet ConfigurationRemove Coupling Block Do not Overtighten Mixing Module and PCD Installation GX-7A and GX-7 400 Models Only Valving Rod AdjustmentGX-7 DI Model Only Initial Set Up Daily Shutdown Daily Start-up Trigger Gun Pressure Relief Procedure Gun Service Kits MaintenanceClean Spray Gun Procedure Flush Gun Repair Service Screen ScrewRemove Centerline Components Remove valving rod. Rod Draw Bar Valving Rod Install Centerline Components GX-7 DI Shown Replace End Cap and Air Piston Assembly Replace Trigger Valve O-Ring Replace Trigger Valve O-Rings Unthread Cap from PCD Body Clean Mixing Module Install Mixing Module Install Mixing Module GX-7A Model Shown Clean Pattern Control Disc Parts GX-7A Model Final Assembly No. Part No. Description GX-7A Model Final AssemblyModule see GX-7A Mix Mod GX-7 DI Model Final Assembly Module see GX-7 DI Model Specifications , GX-7 DI Model Final AssemblyNo. Part No. Description Qty GX-7 400 Model Final Assembly Module Kit , GX-7 400 Model Final Assembly GX-7A Model Handle Assembly Description GX-7 Model Handle Assembly GX-7 DI Model Handle Assembly Description Qty GX-7 DI Model Handle Assembly GX-7 400 Model Handle Assembly GX-7 400 Model Handle Assembly All models Coupling Block Assembly GX-7A Mix Module Kit Specifications Tip Set-Up Chart for GX-7A Model GX-7 400 Mix Module Kit Module Kits Cleanout Drill Iso PortQuantity In/mm Module Only Size Ref Tip Kits for GX-7 400 Gun No. Ref Quantity Set-up Chart for GX-7 400 Model Module/Tip Data for Chemical Sprayed at 2500 PSI Output GX-7 DI Model SpecificationsPattern Lbs/min Round Spray Pattern Tool Kits Tip KitsFor GX-7A and GX-7 DI Models Round Tip Kits Size Quantity Category Data Technical Data Graco Standard Warranty