Table/Blade Guides Parts Breakdown | Grizzly G0621 manual

Table/Blade Guides Parts Breakdown

	��	��	��		��	��
		��	��	��	��
			��	��
						��
��						��
��	��
	��					��
��						��
��
						��
					��	��	��
					��	��
				��	��	��
			��	��		��
			��		��
	��		��		��
	��
		��
		��			��
					��

��

��

��

��

��

��

��

��

				��	��		��
					��		��
					��
					��
					��	��
					��	��
					��
	��
						��	��
			��				��
			��			��
		��				��
	��	��
	��						��
	��
��				��			��
				��			��
		��	��	��	��
	��	��
��	��				��
��	��


	��	��			��
	��	��			��
	��
	��				��
	��				��
	��				��
	��				��	��
	��
	��			��	��
				��	��
			��		��
			��
		��	��	��	��
		��		��	��
		��		��

-48-	G0621 Wood/Metal Bandsaw

Image 50

Grizzly G0621 owner manual Table/Blade Guides Parts Breakdown

Contents

Model G0621 WOOD/METAL Bandsaw Page Table of Contents Contact Info IntroductionForeword Machine Data Sheet G0621 Wood/Metal Bandsaw Identification Safety G0621 Wood/Metal Bandsaw Additional Safety Instructions for Bandsaws 220V Single-Phase Circuit Requirements Items Needed for Setup SetupSetup Safety Unpacking Fasteners and Tools not shown Qty InventoryMain Components Figure Qty Hardware Recognition Chart Site Considerations Clean UpPlacement Location Floor Load Assembly To assemble the bandsawPage Dust port installation G0621 Wood/Metal Bandsaw To center track the blade Dust Collection Blade TrackingTo connect a vacuum hose Test Run Changes in the blade tension may change the blade tracking Tensioning Blade Adjusting Support BearingsTo adjust the support bearings To tension the bandsaw blade G0621 Wood/Metal Bandsaw Adjusting Blade Guides To adjust the upper and lower blade guides To set the positive stop 90˚ to the blade Adjusting Positive StopSetting Table Tilt Scale to 0˚ To calibrate the pointer on the table tilt scale To align the miter slot parallel to the bandsaw blade Aligning TableAligning Fence To align the fence parallel with the miter slot Operation Safety Basic Controls Operations Straight Cuts Workpiece Inspection WoodOverview Irregular Cuts To tilt the table Table TiltGuide Post Positive stop must be removed to move the table to the left To make a 90˚ crosscut RippingCrosscuttingTo make a rip cut Resawing Typical resawing operation Cutting Curves Stacked Cuts To complete a stacked cut Blade Width Blade Selection Wood CuttingBlade Length Tooth Style Blade Breakage Tooth PitchBlade Care Most common causes of blade breakage are Blade Selection Metal Cutting To select the correct blade TPI Blade Changes To replace the blade Scale Calibration To calibrate the scale G7315-Super Heavy-Duty Mobile Base AccessoriesGrizzly Bandsaw Blades G1928-Bandsaw Handbook Schedule MaintenanceCleaning Lubricating Motor & Electrical ServiceTroubleshooting Cutting Operations Miscellaneous Checking V-Belts Accessing V-BeltsServicing V-Belts Tensioning/Replacing V-Belts To skew your fence Shimming Table Blade LeadTo shim the table Wheel Alignment Verifying Upper/Lower Wheels are Coplanar Shimming Upper Wheel Adjusting Lower WheelTo adjust the lower wheel Electrical Component Wiring Motor junction box wiring Wiring Diagram Breakdown Main Parts List Description Table/Blade Guides Parts Breakdown Secondary Parts Breakdown Stand Parts Breakdown Fence Parts Breakdown Safety Labels Parts Breakdown Warranty and Returns Page Page Page