Stand Parts Breakdown | Grizzly G0621 specification

Stand Parts Breakdown

��

��

		��
		��
		��
REF	PART #	DESCRIPTION
201	PB04	HEX BOLT 5/16-18 X 3
202	PW07	FLAT WASHER 5/16
203	P0621203	STAND GUARD
204	P0621204	KNOB 5/16-18 X 3/4
205	PLN03	LOCK NUT 5/16-18
206	PN02	HEX NUT 5/16-18
207	P0621207	STAND
208	P0621208	FOOT

-50-

��

��

��

��

��

��

��

��

��

��

��

��

REF	PART #	DESCRIPTION

209	PB03	HEX BOLT 5/16-18 X 1
210	PN05	HEX NUT 1/4-20
211	PLW02	LOCK WASHER 1/4
212	PW06	FLAT WASHER 1/4
213	P0621213	STAND INSET PLATE
214	P0621214	CABINET BOTTOM PLATE
215	PFB15	FLANGE BOLT 1/4-20 X 3/4

G0621 Wood/Metal Bandsaw

Image 52

Grizzly G0621 owner manual Stand Parts Breakdown

Contents

Model G0621 WOOD/METAL Bandsaw Page Table of Contents Foreword IntroductionContact Info Machine Data Sheet G0621 Wood/Metal Bandsaw Identification Safety G0621 Wood/Metal Bandsaw Additional Safety Instructions for Bandsaws 220V Single-Phase Circuit Requirements Setup Setup SafetyItems Needed for Setup Unpacking Main Components Figure Qty InventoryFasteners and Tools not shown Qty Hardware Recognition Chart Clean Up Placement LocationSite Considerations Floor Load Assembly To assemble the bandsawPage Dust port installation G0621 Wood/Metal Bandsaw To connect a vacuum hose Dust Collection Blade TrackingTo center track the blade Test Run Changes in the blade tension may change the blade tracking Adjusting Support Bearings To adjust the support bearingsTensioning Blade To tension the bandsaw blade G0621 Wood/Metal Bandsaw Adjusting Blade Guides To adjust the upper and lower blade guides Adjusting Positive Stop Setting Table Tilt Scale to 0˚To set the positive stop 90˚ to the blade To calibrate the pointer on the table tilt scale Aligning Table Aligning FenceTo align the miter slot parallel to the bandsaw blade To align the fence parallel with the miter slot Operation Safety Basic Controls Operations Workpiece Inspection Wood OverviewStraight Cuts Irregular Cuts Table Tilt Guide PostTo tilt the table Positive stop must be removed to move the table to the left To make a rip cut RippingCrosscuttingTo make a 90˚ crosscut Resawing Typical resawing operation Cutting Curves Stacked Cuts To complete a stacked cut Blade Selection Wood Cutting Blade LengthBlade Width Tooth Style Tooth Pitch Blade CareBlade Breakage Most common causes of blade breakage are Blade Selection Metal Cutting To select the correct blade TPI Blade Changes To replace the blade Scale Calibration To calibrate the scale Accessories Grizzly Bandsaw BladesG7315-Super Heavy-Duty Mobile Base G1928-Bandsaw Handbook Maintenance CleaningSchedule Lubricating Troubleshooting ServiceMotor & Electrical Cutting Operations Miscellaneous Servicing V-Belts Accessing V-BeltsChecking V-Belts Tensioning/Replacing V-Belts To shim the table Shimming Table Blade LeadTo skew your fence Wheel Alignment Verifying Upper/Lower Wheels are Coplanar To adjust the lower wheel Adjusting Lower WheelShimming Upper Wheel Electrical Component Wiring Motor junction box wiring Wiring Diagram Breakdown Main Parts List Description Table/Blade Guides Parts Breakdown Secondary Parts Breakdown Stand Parts Breakdown Fence Parts Breakdown Safety Labels Parts Breakdown Warranty and Returns Page Page Page