Fence Parts Breakdown | Grizzly G0621 specs

Fence Parts Breakdown

	��
��	��

��

��

��

��

��

��

��

��

��

��

��

��

REF	PART #	DESCRIPTION

300	P0621300	COMPLETE FENCE ASSY
301	P0621301	FENCE BODY
302	P0621302	BUTTON HD CAP SCR M10-1.5 X 16
303	PS09M	PHLP HD SCR M5-.8 X 10
304	P0621304	FENCE BASE
305	PSS03	SET SCREW 1/4-20 X 3/8
306	P0621306	ECCENTRIC SHAFT
307	P6200	BALL BEARING 6200ZZ
308	PR45M	INT RETAINING RING 10MM

REF	PART #	DESCRIPTION

309	P0621309	RUNNER
310	PSB01M	CAP SCREW M6-1 X 16
311	P0621311	FENCE POINTER
312	P0621312	PLATE
313	P0621313	PIN
314	P0621314	LOCK MECHANISM
315	PN03M	HEX NUT M8-1.25
316	P0621316	FENCE HANDLE M8-1.25

G0621 Wood/Metal Bandsaw

-51-

Image 53

Grizzly G0621 owner manual Fence Parts Breakdown

Contents

Model G0621 WOOD/METAL Bandsaw Page Table of Contents Contact Info IntroductionForeword Machine Data Sheet G0621 Wood/Metal Bandsaw Identification Safety G0621 Wood/Metal Bandsaw Additional Safety Instructions for Bandsaws Circuit Requirements 220V Single-Phase Setup Safety SetupItems Needed for Setup Unpacking Fasteners and Tools not shown Qty InventoryMain Components Figure Qty Hardware Recognition Chart Placement Location Clean UpSite Considerations Floor Load To assemble the bandsaw AssemblyPage Dust port installation G0621 Wood/Metal Bandsaw To center track the blade Dust Collection Blade TrackingTo connect a vacuum hose Changes in the blade tension may change the blade tracking Test Run To adjust the support bearings Adjusting Support BearingsTensioning Blade To tension the bandsaw blade G0621 Wood/Metal Bandsaw To adjust the upper and lower blade guides Adjusting Blade Guides Setting Table Tilt Scale to 0˚ Adjusting Positive StopTo set the positive stop 90˚ to the blade To calibrate the pointer on the table tilt scale Aligning Fence Aligning TableTo align the miter slot parallel to the bandsaw blade To align the fence parallel with the miter slot Operations Operation Safety Basic Controls Overview Workpiece Inspection WoodStraight Cuts Irregular Cuts Guide Post Table TiltTo tilt the table Positive stop must be removed to move the table to the left To make a 90˚ crosscut RippingCrosscuttingTo make a rip cut Typical resawing operation Resawing To complete a stacked cut Cutting Curves Stacked Cuts Blade Length Blade Selection Wood CuttingBlade Width Tooth Style Blade Care Tooth PitchBlade Breakage Most common causes of blade breakage are To select the correct blade TPI Blade Selection Metal Cutting To replace the blade Blade Changes To calibrate the scale Scale Calibration Grizzly Bandsaw Blades AccessoriesG7315-Super Heavy-Duty Mobile Base G1928-Bandsaw Handbook Cleaning MaintenanceSchedule Lubricating Motor & Electrical ServiceTroubleshooting Miscellaneous Cutting Operations Checking V-Belts Accessing V-BeltsServicing V-Belts Tensioning/Replacing V-Belts To skew your fence Shimming Table Blade LeadTo shim the table Verifying Upper/Lower Wheels are Coplanar Wheel Alignment Shimming Upper Wheel Adjusting Lower WheelTo adjust the lower wheel Motor junction box wiring Electrical Component Wiring Wiring Diagram Breakdown Description Main Parts List Table/Blade Guides Parts Breakdown Secondary Parts Breakdown Stand Parts Breakdown Fence Parts Breakdown Safety Labels Parts Breakdown Warranty and Returns Page Page Page