Label Placement | Grizzly G0695 instruction

Label Placement

510

502

511

509

503

501

504

513

512

505

508

506

507

REF	PART #	DESCRIPTION

501	P0695501	MACHINE ID LABEL
502	PLABEL-12A	READ MANUAL LABEL
503	PLABEL-55	ENTANGLEMENT HAZARD LABEL
504	P0695504	PREWIRED 220V LABEL
505	P0695505	LIGHT BULB 110V LABEL
506	PLABEL-64B	ELECTROCUTION HAZARD LABEL
507	P0695507	MODEL NUMBER LABEL

REF	PART #	DESCRIPTION

508	G8588	GRIZZLY OVAL NAMEPLATE
509	PLABEL-63	DISCONNECT WARNING LABEL
510	PLABEL-11A	EYE INJURY WARNING LABEL
511	PLABEL-14A	ELECTRICITY LABEL
512	PPAINT-11	GRIZZLY PUTTY TOUCH-UP PAINT
513	PPAINT-1	GRIZZLY GREEN TOUCH-UP PAINT

Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels.

-54-	Model G0695 (Mfg. Since 9/10)

Image 56

Grizzly G0695 owner manual Label Placement

Contents

Model G0695 VS Milling Machine With RAM Head Page Table of Contents Introduction Manual AccuracyContact Info Machine Description Identification Machine Data Sheet Table Info Safety Safety Instructions for MachineryWearing Proper APPAREL. Do not wear Hearing PROTECTION. Always wear hear Safety Instructions for Machinery Additional Safety Instructions For Mills Machine Care and Maintenance Glossary of Terms 220V Single-Phase Operation Circuit Requirements Setup Needed for SetupUnpacking Description Qty Inventory Inventory Figure Qty Cleanup Before cleaning, gather the following Site Considerations Moving & Placing Mill Mounting to Shop Floor Assembly Using Machine MountsBolting to Concrete Floors To assemble your mill Test Run Spindle Break-In Step Control Panel OperationsBasic Controls Table Controls Additional table travel controls Model G0695 Mfg. Since 9/10 Downfeed Controls Operation Overview Table Movement Locks Limit Stops To tilt the head Headstock TiltingTools Needed Qty Hex Bolt Headstock Turret Rotation To rotate the turret Headstock Ram Movement To move the ram inward or outward Setting Spindle Speed Setting Spindle SpeedCalculating Spindle Speed Cutting Speeds for High Speed Steel HSS Cutting Tools Chip Characteristics Loading/Unloading ToolingLoading Tooling Unloading Tooling Accessories G1075-52-PC. Clamping Kit H8370-Power Feed for Mills G9299-10 Yuasa-Type Rotary Table H2689-R-8 Quick Change Collet Set G5641-1-2-3 Blocks G9815-Parallel Set H5556-Edge Finder SetG2861-Face Mill G4051-Carbide Insert for Face Mill G9765-9-PC. Ball End Mill Set G5758-Tilt x G5684-R-8 Vertical Collet RackG5649-5-C Spin Index G1054-Dividing Head-BS-1 G5679-Steel Parallel Set Model G5679 Steel Parallel Set Maintenance Cleaning ProtectingSchedule Lubrication One-Shot Oiler Quill GearingVertical Bevel Gears Lubricant Frequency Qty To tension the V-belt Belt TensioningLeadscrews Motor & Electrical ServiceTroubleshooting Operation Adjusting Gibs Disconnect Mill from Power Before Adjusting the Gibs Adjusting Backlash Belt Replacement To replace the V-beltPage Wiring Wiring Safety Instructions Wiring Diagram Control panel wiring Electrical Components Base, Column, & Knee Breakdown Base, Column, & Knee Parts List Description Head Breakdown Head Parts List Motor & Ram Breakdown Motor & Ram Parts List Table Breakdown Table Parts List Label Placement Warranty Card Comments Grizzly INDUSTRIAL, INC BOX BELLINGHAM, WA Warranty and Returns Warranty and Returns Order Hours a DAY