110V Conversion | Grizzly G0705 guide

110V Conversion

The Model G0705 can be converted for 110V operation. This conversion job consists of dis- connecting the machine from the power source, replacing the contactors and power indicator lamp, and rewiring the motor.

The necessary components for this procedure can be purchased in the Model G0705 110V Conversion Kit (Part No. P0705311) by calling Grizzly Customer Service at (800) 523-4777.

All wiring changes must be inspected by a quali- fied electrician before the machine is connected to the power source. If, at any time during this pro- cedure you need help, call Grizzly Tech Support at (570) 546-9663.

To rewire the Model G0705 for 110V opera- tion:

1.DISCONNECT MACHINE FROM POWER!

2.Remove the electrical box and motor junction box covers shown in Figure 4.

Motor Junction	Indicator Lamp
Box Cover
	Electrical Box
	Cover
Figure 4. Cover locations.

3.Use a Phillips screwdriver to remove all of the wires that connect to the two contactors shown in Figures 5 & 6. If any of the wires are not clearly labeled, label them before removing to ensure that they will be replaced in the proper locations. Refer to SECTION 8: WIRING starting on Page 45 for detailed wir- ing diagrams.

-12-

	V1				13NO	N	A1
							A1
V1			14NO			1L1 N	6
							6
		2T1		CONTACTOR SIEMENS KM1
U2					21NC	L
U2		4T2	22NC		31NC	3L2
	V2				31NC
	V2	6T3 7				8 5L3 L
		6T3 7			43NO	8 5L3 L
N					43NO	4
			44NO			4
	A2	5				4


Contactors		2T1			13NO	4	A1
		2T1			13NO	4	8
		7	14NO			4 1L1 L	8
		5	14NO	CONTACTOR SIEMENS KM2	21NC	4 1L1 L
		4T2 5			31NC	6 3L2 L
N		6T3	32NC		43NO	5L3 L


N	A2		44NO
D

		Control Panel (Viewed From Behind)
				Indicator Light Type XDJ2(J) 220V AC
				Indicator Light Type XDJ2(J) 110V AC
			(Indicator is wired the same for 110V/220V)
			7		5
			4		3
	Indicator		3		4
	Indicator		4	REV	4 FWD
	Lamp		4	REV	4 FWD
	Lamp

X1	POWER
	INDICATOR
1	N LAMP
X2

	EMERGENCY
	STOP			STOP
	BUTTON	1	GND	3 BUTTON
2	2		GND	2	2
2	1	1		1	2
	1	1		1

Figure 5. Partial wiring diagram.

Figure 6. Removing contactors.

Model G0705 (Mfg. since 09/09)

Image 14

Grizzly owner manual 110V Conversion, To rewire the Model G0705 for 110V opera- tion

Contents

Model G0705 Page Table of Contents Contact Info IntroductionManual Accuracy Machine Description Identification Machine Data Sheet Other Features Wearing Proper APPAREL. Do not wear SafetySafety Instructions for Machinery Hearing PROTECTION. Always wear hear Safety Instructions for Machinery Additional Safety for Mill/Drills Full-Load Current Rating Power SupplyAvailability Circuit Information Voltage Conversion Grounding RequirementsExtension Cords Minimum Gauge Size 12 AWG To rewire the Model G0705 for 110V opera- tion 110V Conversion Jumper positions on terminal block Cord rewired for Model G0705 Mfg. since 09/09 Unpacking SetupNeeded for Setup Description Qty Not Shown Crate Contents Figures 11 QtyInventory Cleanup Before cleaning, gather the following Site Considerations Using the Included Leveling Bolt Mounting Options Using Machine Mounts Mounting to Shop Floor To assemble your machine AssemblyMounting to a Workbench To move your machine into position Moving & Placing MachineLeveling Test Run Break-In To break in the spindle Operations Operation Overview Basic Controls Spindle controls Model G0705 Mfg. since 09/09 Head crank To calculate the needed spindle speed in RPM Calculating Spindle Speed for MillingCutting Speeds for High Speed Steel HSS Cutting Tools To change spindle speeds Speed ChangesTools Needed Qty Position Lubrication Suggestions Using the Drill Bit Speed ChartCalculating Spindle Speed for Drilling To operate the micro-adjustment handwheel Spindle Height To remove tooling To install toolingLoading Tooling To use the drift key To install the drill chuck onto the arborDrill Chuck Arbor Collet Adapters Depth Stop To calibrate the depth stop Longitudinal Feed Table TravelGraduated Dials Cross Feed G9299-10 Yuasa-Type Rotary Table AccessoriesH2689-R-8 Quick Change Collet Set G1076-52-PC. Clamping Kit G9765-9-PC. Ball End Mill Set H8370-Power Feed for MillsG2861-Face Mill G4051-Carbide Insert for Face Mill G5641-1-2-3 Blocks G9815-Parallel Set H5556-Edge Finder Set Schedule MaintenanceCleaning Protecting Points requiring periodic lubrication are LubricationTable Leadscrews Items Needed Qty Belts Belt tension Model G0705 Mfg. since 09/09 Service Troubleshooting Symptom Possible Cause Possible Solution Gibs Return Spring To adjust the table gibsTo adjust the spring tension Adjusting spring tension Tighten the black thumb knob Leadscrew Backlash Wiring Wiring Safety Instructions G0705 Wiring Diagram Electrical component locations Headstock Headstock Parts List Description PCAP05 Base Base Parts List Electrical Components Breakdown and List 309 Labels Breakdown and List Warranty Card Comments Grizzly INDUSTRIAL, INC BOX BELLINGHAM, WA Warranty and Returns Warranty and Returns Order Hours a DAY