GAS Insert Aeration System | Hampton Direct U32 guide

INSTALLATION

Be careful not to damage thermal insula- tion when sliding on vent connector plate.

This could cause blockage.

9)Connect the 2nd liner to the exhaust collar marked with an "E", seal connection with high temperature silicone. Secure with gear clamp.

NOTES:

1)Final gas connection should be made after unit is in place to avoid damage to line when pushing the unit into position.

2)Mill-pac may be used instead of high temperature silicone and screws may be used instead of gear clamps at connections of liner to inlet and vent collars.

1)Make sure the valve is in the "OFF" position.

2)Loosen the "IN" and/or "OUT" pressure tap(s), turning counterclockwise with a 1/8" wide ﬂ at screwdriver.

3)Attach manometer to "IN" and/or "OUT" pressure tap(s) using a 5/16" ID hose.

4)Light the pilot and turn the valve to "ON" position.

5)The pressure check should be carried out with the unit burning and the setting should be within the limits speciﬁ ed on the safety label.

6)When ﬁ nished reading manometer, turn off the gas valve, disconnect the hose and tighten the screw (clockwise) with a 1/8" ﬂ at screwdriver. Note: Screw should be snug, but do not over tighten.

GAS INSERT

AERATION SYSTEM

The air shutter can be adjusted by moving the adjusting wire up or down. The wire is accessed through the bottom louver opening. Open the air shutter for a blue ﬂ ame or close for a yellower

ﬂame. The burner aeration is factory set but may need adjusting due to either the local gas supply or altitude.

Minimum Air Shutter Opening:

3/16" Natural Gas

1/4" Propane

OPTIONAL

BRICK PANEL

1)Unwrap the brick pattern panels from the protective wrapping.

2)Remove the glass front if it is already installed, see "Standard Flush Door" section.

3)Put the rear brick panel ﬂ at against the back of the unit.

4)Beforeinstallingthesidebrickpanels,loosen the screws for the brick tabs enough so that you can slide the brick tabs on to the screws easily but that the tabs are secure. For the location of the side brick tab screws see diagram 1.

GAS PIPE

PRESSURE TESTING

The appliance must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig. (3.45 kPa). Disconnect piping from valve at pressures over 1/2 psig.

Themanifoldpressureiscontrolledbyaregulator built into the gas control, and should be checked at the pressure test point.

Note: To properly check gas pressure, both inlet and manifold pressures should be checked using the valve pressure ports on the valve.

Aeration Adjustment Wire

PULL= Open

PUSH = Close

CAUTION:Carbonwillbe produced if air shutter is closed too much.

Note:anydamageduetocarboningresulting fromimproperlysettingtheaerationcontrols is NOT covered under warranty.

Note: Aeration Adjustment should only be performed by an authorized FPI Installer at the time of installation or service.

Diagram 1

5)Remove the brick tabs and slide the side brick panels into position. See diagram 1. Install the brick tabs. See diagram 2.

Diagram 2

U32-5 FPI Direct Vent Gas Insert

U32 specifications

Hampton Direct U32 is a versatile and innovative product designed to enhance everyday living. This device serves as an all-in-one solution, combining functionality, convenience, and modern technology to meet the needs of today's consumers.

One of the standout features of the Hampton Direct U32 is its user-friendly interface. The device comes equipped with a high-resolution touchscreen display, allowing users to navigate through various functions effortlessly. This intuitive design ensures that individuals of all ages can operate the U32 without frustration or difficulty.

The U32 also boasts a range of connectivity options, including Bluetooth and Wi-Fi capabilities. This enables users to connect the device to their smartphones, smart home systems, or other peripherals, making it a seamless addition to any tech-savvy lifestyle. With the ability to sync with mobile applications, users can access a broad range of features, from remote control functions to personalized settings tailored to their preferences.

In addition to connectivity, the Hampton Direct U32 incorporates advanced technology such as voice recognition. This feature allows users to control the device hands-free, enhancing convenience and providing an intuitive experience. The voice command functionality can access various features, further simplifying routine tasks and fostering a more connected environment.

Moreover, the U32 is designed with energy efficiency in mind. Utilizing modern energy-saving technologies, this device minimizes power consumption while delivering reliable performance. It is not just about functionality; the U32 is built to be eco-friendly, appealing to environmentally conscious consumers who wish to reduce their carbon footprint.

Another remarkable characteristic of the Hampton Direct U32 is its durability. Constructed from high-quality materials, the device is designed to withstand daily wear and tear while maintaining optimal performance. This robustness ensures that users can rely on the U32 long-term, making it a worthwhile investment.

Overall, the Hampton Direct U32 stands out as a multifunctional device that combines cutting-edge technology, user-friendly design, and energy efficiency. It successfully addresses the demands of modern living by offering robust features that cater to convenience, connectivity, and sustainability, making it an essential tool for households looking to simplify and enhance their daily routines.

Hampton Direct U32 GAS Insert Aeration System, Optional Brick Panel, GAS Pipe Pressure Testing

Models: U32