Harman-Kardon Car Stereo System, 376, DPR 2005 owner manual REAR-PANEL Connections

REAR-PANEL CONNECTIONS

dSwitched AC Outlet: These outlets may be used to power any device you wish to have turned on when the DPR 2005 is turned on with the Standby/On Switch 1.

NOTE: The total power consumption of all devices connected to the rear panel AC outlets should not exceed 100 watts.

eFront Speaker Outputs: Connect these outputs to the matching + or – terminals on your left and right speakers. When making speaker connections always make certain to maintain correct polarity by connecting the color-coded (white for front left and red for front right) (+) terminals on the DPR 2005 to the red (+) terminals on the speakers and the black (–) terminals on the DPR 2005 to the black (–) terminals on the speakers. See page 16 for more information on speaker polarity.

fSurround Speaker Outputs: Connect these out- puts to the matching + and – terminals on your sur- round channel speakers. In conformance with the CEA color-code specification, the blue terminal is the posi- tive, or “+” terminal that should be connected to the red (+) terminal on the Surround Left speaker with older color-coding, while the gray terminal should be connected to the red (+) terminal on the Surround Right speaker with the older color-coding. Connect the black (–) terminal on the DPR to the matching black negative (–) terminals for each surround speaker. (See page 16 for more information on speaker polarity.)

gSurround Back/Multiroom Speaker Outputs: These speaker terminals are normally used to power the surround back left/surround back right speakers in a 7.1 channel system. However, they may also be used to power the speakers in a second zone, which will receive the output selected for a multiroom system. To change the output fed to these terminals from the default of the Surround Back speakers to the Multiroom Output, you must change a setting in the MULTI-ROOM SETUP menu of the OSD system. See page 39 for more information on config- uring this speaker output. In normal surround system use, the brown and black terminals are the surround back left channel positive (+) and negative (–) con- nections and the tan and black terminals are the sur- round back right positive (+) and negative (–) termi- nals. For multiroom use, connect the brown and black SBL terminals to the red and black connections on the left remote zone speaker and connect the tan and black SBR terminals to the red and black terminals on the right remote zone speaker.

hCenter Speaker Outputs: Connect these outputs to the matching + and – terminals on your center channel speaker. In conformance with the CEA color- code specification, the green terminal is the positive, or “+” terminal that should be connected to the red

(+) terminal on speakers with the older color-coding. Connect the black (–) terminal on the DPR to the black negative (–) terminal on your speaker. (See page 16 for more information on speaker polarity.)

iComponent Video 1 Inputs: These inputs may be used with any video source device equipped with analog Y/Pr/Pb or RGB component video outputs. The factory default is for these jacks to be linked to the DVD input, but you may change the setting at any time through the IN/OUT SETUP menu. See page 21 for more information on configuring the component video inputs.

jComponent Video 2 Inputs: These inputs may be used with any video source device equipped with analog Y/Pr/Pb or RGB component video outputs. The factory default is for these jacks to be linked to the Video 2 input, but you may change the setting at any time through the IN/OUT SETUP menu. See page 21 for more information on configuring the com- ponent video inputs.

kComponent Video Monitor Outputs: Connect these outputs to the component video inputs of a video projector or monitor. When a source connected to one of the Component Video Inputs ij is selected the signal will be sent to these jacks.

31Multiroom IR Input: Connect the output of an IR sensor in a remote room to this jack to operate the DPR 2005’s multiroom control system.

32Remote IR Input: If the DPR 2005’s front- panel IR sensor is blocked due to cabinet doors or other obstructions, an external IR sensor may be used. Connect the output of the sensor to this jack.

33Remote IR Output: This connection permits the IR sensor in the receiver to serve other remote con- trolled devices. Connect this jack to the “IR IN” jack on Harman Kardon (or other compatible) equipment.

34A-BUS Connector: Connect this jack to an optional A-BUS®-certified remote room keypad or amplifier to extend the multiroom capabilities of your DPR 2005. See page 39 for more information on A-BUS.

35FM Antenna: Connect the supplied indoor or an optional external FM antenna to this terminal.

36AM Antenna: Connect the AM loop antenna sup- plied with the receiver to these terminals. If an external AM antenna is used, make connections to the AM and GND terminals in accordance with the instructions supplied with the antenna.

10 REAR-PANEL CONNECTIONS