![](/images/new-backgrounds/1217073/21707359x1.webp)
OPERATION
Basic Operation
Once you have completed the initial setup and configu- ration of the DPR 2005, it is simple to operate and enjoy. The following instructions will help you maximize the enjoyment of your new receiver:
Turning the DPR 2005 On or Off
•When using the DPR 2005 for the first time, you must press the Main Power Switch A to turn the unit
on. This places the unit in a Standby mode, as indi- cated by the Standby/On Indicator 1 turning amber.
Once the unit is in Standby, you may begin a listening session by pressing the Standby/On Button 2 on the front panel, or the Power On Button b or AVR Selector e∫ on the remote. This will turn the unit on and return the DPR to the input source that was last used. The unit may also be turned on from Standby by pressing any of the Input Selector
Buttons d ç∂ on the remote or the Input Source Selector Button 8 on the front panel.
Whenever the DPR is turned on, you will see all of the
NOTE: After pressing one of the Input Selector
Buttons d ç∂ to turn the unit on, press the AVR Selector e∫ to set the remote control to the DPR 2005 functions.
To turn the unit off, simply press the Standby/On Switch 1 on the front panel or the Power Off Button aå on the remote. Power will be shut off to any equipment plugged into the
When the remote is used to turn the unit “off,” it is actually placing the system in a Standby mode, as indicated by the amber lighting of the Standby/On Indicator 1.
• To program the DPR 2005 for automatic
press the Sleep Button on the remote. Each press of the button will decrease the time before
The sleep time will be displayed in the Lower Display Line & and it will count down until the time has elapsed.
The
the Lower Display Line &. When the programmed sleep time has elapsed, the unit will turn off.
When you will be away from home for an extended period of time, it is always a good idea to turn the unit off with the
NOTE: All preset memories are lost if the unit is left turned off by using the Main Power Switch A for more than four weeks.
Source Selection
•To select a source, press any of the Input Selector
Buttons d ç∂ on the remote.
•The input source may also be changed by pressing the
•When a new input is selected, the DPR will automati- cally switch to the digital input (if selected), surround mode, component video input, A/V Sync Delay and Night Mode configurations that were in effect the last time that input was used. If the BASS MGR line on the SPEAKER SETUP menu (Fig. 7) was set to INDEPENDENT, as described on page 26, the settings for speaker size will also change to the preset values.
•The
•As the input source is changed, the new input name will appear momentarily as an
•When an audio source is selected, the last video input used remains routed to the Video 1/Video 2 Outputs £∞ and Video Monitor Outputs •. This permits simultaneous viewing and listening to different sources.
•When a composite or
video signal for that input will be routed to the Video Monitor Output • and will be viewable on a TV monitor connected to the DPR 2005.
6-Channel/8-Channel Direct Input
•There are two input choices available for use with sources such as a
■The 6 CH DVD AUDIO input should be used when the SBR and SBL inputs are not
in use. When this input is used, the analog source is converted to digital so that you may use the same
■The 8 CH DVD AUDIO input should
be used when an input is connected to all eight
Volume and Tone Control
•Adjust the volume to a comfortable level using the .
•To temporarily silence all speaker outputs, press the
Mute Button 33 . This will interrupt the out- put to all speakers and the headphone jack, but it will not affect any recording or dubbing that may be in progress. When the system is muted, the word MUTE will flash in the
33 again to return to normal operation.
•The unit’s tone controls may be taken out of the
signal path by pressing the Tone Mode Button on
the front panel B or the remote . The first press of either button will show a message in the
•When the tone controls are active, the bass and tre- ble boost/cut may be adjusted by first pressing the
Tone Mode Button on the front panel B or the
remote until the desired setting (BASS MODE or TREBLE MODE) appears in the
•For private listening, simply place a standard 1/4" stereo headphone plug or adaptor into the