![](/images/new-backgrounds/1217073/21707391x1.webp)
CONFIGURING THE REMOTE
next to the bracketed
6.When you are finished reviewing the macro’s contents, press the Set Button q to return the remote to normal operation.
Punch-Through Configuration
Volume Punch-Through
Follow these steps to enable the Volume Up/Down and Mute controls from one device to be used when the remote is otherwise programmed for a different device.
NOTE FOR VOLUME
1.Press and hold the Program Button O for about three seconds while the message shown in Figure 18 appears in the remote’s LCD Information Display 2. Release the button when the red light under the Set Button q appears.
2.The remote’s MAIN MENU message (Figure 19), will appear in the LCD display and the Set Button q will remain illuminated in red. Press the ⁄ / ¤ Navigation Button o until
M A I N M E N U
P U N C H - T H R O U G H
Figure 51
3.At the next menu screen (Figure 52) press the Set Button q to begin programming the remote for Volume
P U N C H - T H R O U G H
V O L U M E
Figure 52
4.The next display screen (Figure 53) is where you select the device that will receive the punch- through commands. In our example, that is the VID 2/TV button, as that is where we want the DPR 2005’s volume controls to be active. Press the ⁄ / ¤ Navigation Button o until the name of the base device appears and then press the Set Button q.
D E V I C E I N U S E
T V
Figure 53
5.At the next display screen (Figure 54), you will select the device whose Volume Up/Down and Mute commands will be used. Press the ⁄ / ¤ Navigation Button o until the desired device’s name appears to the right of the device in use. In our example, that is the DPR 2005 (indicated by DPR). When the desired combination of devices appears, press the Set Button q.
P U N C H - T H R O U G H
T V < - A V R
Figure 54
6.When the Set button is pressed, the display will change to show you that the new combination of control commands is being saved to the unit’s memory, as shown in Figure 55. The word SAVED will flash four times and then the remote will return to normal operation.
T V < - A V R [ V O L ]
S A V E D
Figure 55
7.Once the
is in use.
Returning the Volume Control Settings to Default Operation
If you wish to remove the Volume
P U N C H - T H R O U G H
T V < - T V
Figure 56
Channel Punch-Through
Channel
would want the Channel Up/Down Buttons to transmit commands to the cable box even though the other button commands are programmed to operate the VCR.
To program the remote for channel
1.Press and hold the Program Button O for about three seconds while the message shown in Figure 18 appears in the remote’s LCD Information Display 2. Release the button when the red light under the Set Button q appears.
2.The remote’s MAIN MENU message (Figure 19), will appear in the LCD display and the Set Button q will remain illuminated in red. Press the ⁄ / ¤ Navigation Button o until
3.At the next menu screen, press the ⁄ / ¤ Navigation Button o until CHANNEL appears on the bottom line of the LCD screen, as shown in Figure 57. Press the Set Button q to begin programming the remote for channel
P U N C H - T H R O U G H
C H A N N E L
Figure 57
4.The next display screen (Figure 58) is where you select the device that will receive the punch- through commands. In our example, that is the VID 1/VCR button, as that is where we want the cable box’s channel controls to be active. Press the ⁄ / ¤ Navigation Button o until the name of the base device appears and then press the Set Button q.
D E V I C E I N U S E
V C R
Figure 58
5.At the next display screen (Figure 59), you will select the device whose Channel Up/Down com- mands will be used. Press the ⁄ / ¤ Navigation
46 CONFIGURING THE REMOTE