Zone 2 Remote Control Functions

Power Off

Not Used

AVR Settings

Back/Exit

Volume Controls

Zone Selector

IR Transmitter

Mute

Source Selectors

Sleep Settings

Info Settings

Navigation

Transport Controls

Zone Indicator

NOTE: To make it easier to follow the instructions throughout the manual that refer to this illustration, a copy of this page may be downloaded from the Product Support section at www.harmankardon.com.

Page 15

Image 15

Harman-Kardon AVR 3550HD owner manual Zone 2 Remote Control Functions

Contents

AVR 3550HD Important Safety Instructions Safety Information Do not place the unit directly on a carpeted surface Important Safety Information Table of Contents Audio Section IntroductionHarman Kardon AVR 3550HD 7.1-Channel Audio/Video Receiver Thank you for choosing a Harman Kardon product Digital Audio Inputs Supplied AccessoriesAudio Inputs Audio/Video Inputs FRONT-PANEL Controls Power Indicator This LED has three possible modes On When the AVR is turned on, this LED turns whiteVolume Knob Turn this knob to raise or lower the volume REAR-PANEL Connections REAR-PANEL Connections REAR-PANEL Connections Main Remote Control Functions Main Remote Control Functions Main Remote Control Functions Zone 2 Remote Control Functions Zone 2 Remote Control Functions Multichannel Audio Introduction to Home TheaterSurround Modes Typical Home Theater System Subwoofer Connecting Source Devices to the AVRConnections Speaker Connections Hdmi cable runs are limited to about 10 feet Video ConnectionsDigital Video Analog Video FM antenna uses a 75-ohm F-connector. See Figure AntennasRS-232 Serial Port Placement of Surround Speakers in a 7.1-Channel System Speaker PlacementFront Speaker Placement Placement of Surround Speakers in a 5.1-Channel System Step Three Connect the Antennas InstallationStep One Connect the Speakers Step Two Connect the Subwoofer Hdmi Video Connect the player as shown in Figure Audio Connections for non-HDMI sourcesVideo Connections for non-HDMI sources Choose one digital audio connection Optical or Coaxial Hdmi Video Connect the recorder as shown in Figure Connect an Audio/Video Recorder PVD, DVR or TiVo Connect a Tape Deck or Any Audio-Only Recorder Connect an iPod Using Docking StationConnecting a Game Console, Camera or Other Device Connect a CD Player or Any Audio-Only Device Step Five Connect the Video Display Step Six Plug in AC Power Step Seven Insert Batteries in Remote Enter a code from , aboveSatisfactory code set that operates most functions Learning Step Ten Install a Multizone System Optional Zone 2 Audio Outputs Step Eleven Turn On the AVR 3550HD AVR Power On and Source Selectors Initial Setup Using the On-Screen Menu SystemConfigure the AVR 3550HD Using EzSet/EQ Technology Select Cancel to return to the Speaker Setup menu Set Up Sources Audio and Video Input Selection Channel Direct InputsHDMI-Equipped Multichannel Disc Player You are now ready to begin enjoying your new receiver ‹ / › Buttons to delay the audio by up to 180ms. See Figure Operation Using the Tuner Source SelectionXM Radio Operation Recording Using Docking StationTo store a channel in one of the 40 preset locations Press the OK Button to store the new preset Selecting a Surround Mode Press the Menu Button to view the slide-out menuMusic Navigates the audio materials stored on the iPod Auto SELECT, Surr VIRTUAL, Surr STEREO, Surr MOVIE, Surr CH Stereo plays the left-channel signal through the front Audio Processing and Surround Sound Analog Audio SignalsDigital Audio Signals Advanced Functions Indicates that no surround information is present Dolby Surround Settings Step Two Measure Speaker Distances Manual SetupStep Three Manual Setup Menu Night Mode Adjust Crossover Frequencies Menu Sub ModeNumber of Speakers Adjust Speaker Distance Menu Step Four Setting Channel Output Levels Manually Tone Control Determines whether the treble and bass Video Adjustments Sports For sporting events How to Adjust the Custom Picture SettingsBrightness Adjustment Nature For programs shot outdoors, in a natural setting Multizone Operation Menu Appearance System SettingsGeneral AVR Settings Operating the Multizone System Activities Macros Advanced Remote Control FunctionsResetting the Remote Punch-Through Programming Memory Processor Reset Troubleshooting Guide Table A1 Recommended Source Component Connections Appendix Default settings, worksheets, remote product codesTable A2 Source Setting Defaults Appendix Table A4 Delay Setting Defaults Table A3 Speaker/Channel Setting Defaults Table A5 Source Settings Table A6 Audio Effects SettingsTable A7 Video Modes Settings Table A9 Remote Control Codes Table A10 System SettingsTable A8 Surround Modes Table A12 Surround Modes Table A11 Zone 2 Settings Music adds a surround back channel Analog 2-channel Tuner Mode Group Enveloping sound field is desiredExperience Tuner Movie Back channel 0 or .1, EX Analog 2-channel Tuner DTS Stereo Surround Mode Description Incoming Bitstream or SignalRate used on DVD-Video discs Performance Via Hdmi DTS-ES Matrix Analog Bypass Appropriate when a subwoofer is usedChannel Stereo Channels Tuner PCM 32kHz, 44.1kHz or 48kHz Channel Stereo 41 42 Table A13 Remote Control Function List RadioDMC1000 Game Power OffTable A13 Button Name Aiwa Table A16 Table A16 Remote Control Product Codes AUX-VCRTable A15 Remote Control Product Codes AUX-HDTV Table A14 Table A17 Table A18 Remote Control Product Codes DVD Table A19 Remote Control Product Codes SAT Table A20 Remote Control Product Codes GameTable A21 Remote Control Product Codes CBL Table A21 Table A22 Remote Control Product CodesTable A23 Remote Control Product Codes Table A24 Remote Control Product Codes AUX- TiVo Linear High-Level 200mV/47k ohms General Power Requirement AC 120V/60Hz Power ConsumptionChannels driven Dimensions Product Shipping Width Product Shipping Weight 31.5 lb 14.3kg 36.7 lb 16.7kg