MAIN REMOTE CONTROL FUNCTIONS
IMPORTANT NOTE: The DPR 1005’s remote may be programmed to control up to nine devices, including the DPR 1005. Before using the remote, it is important to remember to press the Input Selector Button 3 that corresponds to the unit you wish to operate. In addition, the DPR 1005’s remote is shipped from the factory to operate the DPR 1005 and most Harman Kardon CD or DVD players and cassette decks. The remote is also capable of operating a wide variety of other products using the control codes that are part of the remote. Before using the remote with other products, follow the instructions on pages 41 – 50 to program the proper codes for the products in your system.
It is also important to remember that many of the buttons on the remote take on different functions, depending on the product selected using the Input Selectors d. The descriptions shown here primarily detail the functions of the remote when it is used to operate the DPR 1005.
aPower Off Button: Press this button to place the DPR 1005 or a selected device in the Standby mode. Note that this will turn off the main room functions, but if the Multiroom system is activated, it will continue to function.
1Power On Button: Press this button to turn on the power to a device selected by first pressing one of the Input Selectors 3.
2LCD Information Display: This
3Input Selectors: Pressing one of these buttons will perform three actions at the same time. First, if the DPR 1005 is not turned on, this will power up the unit. Next, it will select the source shown on the button as the input to the DPR 1005. Finally, it will change the remote control so that it controls the device selected. After pressing one of these buttons you must press the AVR Selector Button 4 again to operate the DPR 1005’s functions with the remote.
4AVR Selector: Pressing this button will switch the remote so that it will operate the DPR 1005's functions. If the DPR 1005 is in the Standby mode, it will also turn the DPR 1005 on.
5Test Button: Press this button to begin the sequence used to calibrate the DPR 1005’s output levels. (See page 27 for more information on calibrat- ing the DPR 1005.)
gDSP Surround Mode Selector: Press this button to select one of the DSP surround modes, such as VMAx, Hall 1, Hall 2 or Theater. Each press of the button selects another mode. (See page 32 for more information on surround modes.)
7Logic 7 Mode Select Button: Press this button to select from among the available Logic 7 surround modes. (See page 32 for the available Logic 7 options.)
8Direct Button: Press this button when the tuner is in use to start the sequence for direct entry of a station’s frequency. After pressing the button, simply press the proper Numeric Keys A to select a station. (See page 35 for more information on the tuner.)
9Clear Button: When programming the remote or using the EzSet feature, press this button to cancel the current function. When using the remote to enter frequencies for direct tuner access, press this button to clear previous entries.
ANumeric Keys: These buttons serve as a ten- button numeric keypad to enter tuner preset positions. They are also used to select channel numbers when TV, Cable or SAT has been selected on the remote, or to select track numbers on a CD, DVD or LD player, depending on how the remote has been programmed. These buttons are also used to enter letters and num- bers when renaming devices in the LCD Information Display. (See page 48 for more information on renam- ing devices and keys.)
BTuning Mode Button: Press this button to change the tuner mode between manual and automatic. When the button is pressed so that AUTO/STEREO appears in the Upper Display Line ^ and in the
mDim Button: This button activates the Dimmer function, which reduces the brightness of the front- panel display, or turns it off entirely. Press the button once to reduce the display brightness by 50%, and press it again within five seconds and the main display will go completely dark. Note that this setting is tem- porary; regardless of any changes, the display will always return to full brightness when the DPR is turned on. The blue accent lighting inside the volume control will go out when the panel lights are at half brightness or when they are fully dimmed.
nChannel Select Button: This button is used to start the process of setting the DPR 1005’s output levels to an external source. Once this button is pressed, press the ⁄/¤ on the Navigation Button o to select the channel being adjusted, then press the Set Button q, followed by the ⁄/¤ on the Navigation Button o again, to change the level setting. (See page 36 for more information.)
oNavigation Button: This single
pDigital Select Button: Press this button to assign one of the digital inputs fl‡HJ to a source. (See page 33 for more information on using digital inputs.)
qSet Button: This button is used to enter settings into the DPR 1005’s memory. It is also used in the setup procedures for delay time, speaker configuration and channel output level adjustment.
HVolume Up/Down Buttons: These controls share the disc in the lower portion of the remote with
the Channel Up/Down Selector . To raise the
volume, press the button marked ⁄ by pressing towards the top of the remote. To lower the volume, press the button marked ¤ by pressing towards the bottom of the remote. The ‹/› buttons on the left and right sides of this disc change channels up or down when the TV, cable box or satellite Input Selectors
