Harman-Kardon DPR 1005 owner manual Delay Settings, System Configuration

SYSTEM CONFIGURATION

* * S P E A K E R S E T U P					* *
→ M O D E
		: S I Z E		X - O V E R
L E F T / R I G H T :			1 0 0 H Z
C E N T E R		:	1 0 0 H Z
S U R R O U N D		:	1 0 0 H Z
S U R R	B A C K	:	1 0 0 H Z
L F E		: L E F T / R I G H T
B A S S	M G R	:	G L O B A L
B A C K	T O M A S T E R M E N U

Figure 8

To change the setting for any of the four speaker groups, press the ⁄/¤ Navigation Button o until the cursor is next to the speaker group where you wish to make a change and then press the ‹/› Navigation Button o until the desired setting appears. The available choices for low-frequency information to be sent to the subwoofer, rather than to the main speaker channel, are 40Hz, 60Hz, 80Hz, 100Hz, 120Hz and 200Hz. Pick the choice that is identical to the information for the speakers, or if an exact match is not possible, pick the closest choice that is ABOVE the speaker’s low-frequency limit or crossover point to avoid the creation of a low- frequency “hole” where your system will have no bass information.

The setting for the crossover point for the LFE chan- nel, which is created to provide specific low-frequency information in many movies with digital soundtracks, may be set to match the crossover for any of the four speaker groups. Since the crossover point commonly used in the creation of the LFE channel is 120Hz, we recommend that you select the speaker group whose crossover point is closest to 120Hz. To do this, press the ⁄/¤ Navigation Button o until the cursor is next to the LFE line, and then press the ‹/› Navigation Button o until the name of the speaker group with the desired crossover frequency appears. Of course, you may also experiment with different settings to find the one that provides the smoothest and most complete bass response in your particular listening environment.

When all crossover settings have been made, or in those cases where none are needed, press the ¤ Navigation Button o so that the cursor is next to the BASS MGR line to make the final setting on this menu.

This setting allows you to use the same speaker con- figuration and crossover settings for all inputs, or to have different settings for each input. In most cases, the factory default setting of GLOBAL will be appropriate, as most systems do not need individual speaker settings. However, when full-range front speakers are used for both movies and music, differ- ent bass management settings may be used when listening to music through a CD player as opposed

to a movie from a DVD player, VCR or cable/satellite set-top.

To customize the speaker-size configurations to each input, make certain that the MODE line of the SPEAKER SETUP menu is set to SIZE, and that the cursor is on the BASS MGR line. Press the ‹/› Navigation Button o so that INDEPENDENT appears in highlighted video. When this choice is entered by exiting the menu, the settings just entered will apply to the current input ONLY, and you will need to go back to the IN/OUT menu to select another input, and then return to this menu page to change the settings for the next input. Repeat the procedure for any input where you wish to have a different set of speaker con- figuration and crossover settings.

NOTE: The inidependent feature allows you to select a different speaker size configuration (Large, Small or None, as appropriate) for each input source. However, the individual crossover point setting may only be set once, and the selection made during the initial setup will be used for all inputs, regardless of any changes made to the “Large” or “Small” settings for the speaker groups attached to any input. The reason is that while you may prefer different settings for the bass redirec- tion (that is, which signals go to the subwoofer or the speaker group), the actual crossover point remains the same since the actual loudspeakers themselves remain the same regardless of any other setting.

When all speaker selections have been made, press the ¤ Navigation Button o and then the Set Button q to return to the MASTER MENU.

Delay Settings

Due to the different distances between the listening position and each speaker position, the amount of time it takes for sound to reach your ears from each channel is different. You may compensate for this dif- ference through the use of the delay settings to adjust the timing for the speaker placement and acoustic conditions in your listening room or home theater.

The DPR 1005’s advanced software enables you to quickly and easily set delay times without the need to calculate them using a complex formula. Instead, all you need to do is measure the approximate distance between your listening position and each of the speakers in your system. When you enter those dis- tances into the DPR’s memory as shown below, the DPR’s microprocessor does the rest of the work, cal- culating the proper delay time. The measurements need not be accurate to the inch, as the system is designed to accommodate a typical listening area rather than require the precise measurement to one “sweet spot” position.

In addition to adjusting the delay time for each individ- ual speaker position, the DPR 1005 is among the few receivers that allows you to adjust the delay for the combined output of all speakers as a group. This fea- ture is called A/V Sync Delay; it allows you to com- pensate for delays to the video image that may be caused by the processing in products such as digital video displays, video scalers, digital cable or satellite systems, or personal video recorders. With proper adjustment of the setting for A/V Sync Delay, you can eliminate the loss of lip sync that may be caused by digital video applications.

Due to the differences between the way surround modes operate, some modes allow for a greater range of delay times than others. To avoid problems, we rec- ommend that delay times be adjusted using the Dolby Digital mode. If a different mode is selected at a later time, the DPR 1005 will automatically select the closest delay settings available for the surround mode in use.

Delay times are adjustable only for the Dolby and DTS modes, so you will notice that the DELAY menu may not be accessed for other modes, such as Logic 7. In addition, when a non-Dolby Digital mode such as Pro Logic II is selected, adjustments may be made to the Surround speakers only.

To set the delay time for a specific input, the DELAY ADJUST menu (Figure 9) should be visible on your on-screen display. If the system is not already at that point, press the OSD Button

to bring up the MASTER MENU and press the

¤Navigation Button o until the on-screen ➔ cursor is pointing at the DELAY ADJUST line. Press the Set Button q to call up the menu.

	*	D E L A Y		A D J U S T *
→	F L	: 1 2 f t		S B R : 1 0 f t
	C E N : 1 2 f t			S B L : 1 0 f t
	F R	: 1 2 f t		S L : 1 0 f t
	S R	: 1 0 F t		S U B : 1 0 f t
	U N I T :		F E E T	M E T E R
	A / V S Y N C			D E L A Y : 0 m S

B A C K T O M A S T E R M E N U

Figure 9

Once the DELAY ADJUST menu is on your screen, note that the default for distance settings is in feet. If your measurements are in feet, proceed to the next step; if your measurements are made in meters, press the ¤ Navigation Button o until the on- screen ➔ cursor is at the UNIT line on the menu. Then, press the ‹/› Navigation Button o so that METER is highlighted. When the change

in measurement units is made, press the ⁄/¤

26 SYSTEM CONFIGURATION