OPERATION
5. Press the Set Button q to enter the change.
6. Press the OSD Button | to exit the menus and |
return to normal operation. |
|
Once the setting is made, the Input/Output Status Indicator I will turn red, indicating that the jacks are now an output, instead of in the default setting as an input. Once changed to an output, the setting will remain as long as the DPR 1005 is turned on, unless the setting is changed in the OSD menu system, as described above. However, once the DPR 1005 is turned off, the setting is cancelled. When the unit is turned on again, the
to use the jacks as an output at a future time, the setting must be changed again using the OSD menu system, as described above.
Output Level Trim Adjustment
Normal output level adjustment for the DPR 1005 is established using the test tone, as outlined on pages 27 – 29. In some cases, however, it may be desirable to adjust the output levels using program material such as a test disc, or a selection you are familiar with. Additionally, the output level for the subwoofer can only be adjusted using this procedure.
To adjust the output levels using program material, first set the reference volume for the front left and front right channels using the Volume Control #rî.
If you are using a disc with test signals or an external signal generator as the source used when the output levels are being trimmed, you may use the remote as an SPL meter to guide you to the correct level set- tings. To use the EzSet remote as an SPL meter, follow the instructions on page 29.
Once the reference level has been set, press the Channel Select Button n and FRONT L LEVEL will appear in the Lower Display Line &. To change the level, first press the Set Button
q, and then use the ⁄/¤ Navigation Button o to raise or lower the level. DO NOT use the vol- ume control, as this will alter the reference setting.
Once the change has been made, press the Set Button q and then press the ⁄/¤ Navigation Button o to select the next
Repeat the procedure as needed until all channels requiring adjustment have been set. When all adjust- ments have been made and no further adjustments
are made for five seconds, the DPR 1005 will return to normal operation.
The channel output for any input may also be adjusted using the
Button to bring up the MASTER MENU (Fig. 1). Press the ¤ Navigation Button o until the
Once the menu appears on your video screen, first use the ⁄/¤ Navigation Button o to move the
‹/› Navigation Button o to change the output level. Remember, the goal is to have the output level at each channel be equal when heard at the listening position.
If you wish to reset all the levels to their original factory default of 0dB offset, press the ⁄/¤ Navigation Button o so that the
qif you wish to go back to the main menu to make other adjustments. If you have no other adjust-
ments to make, press the OSD Button | to exit |
the menu system. |
|
NOTE: Output levels may be separately trimmed for each surround mode. If you wish to have different trim levels for a specific mode, select that mode and then follow the instructions shown above.
Dim Function
Since the DPR 1005 will often be used when movies or other video programming is viewed under
Simply press the Dim Button m once to dim the front panel to half the normal brightness level; press it again to turn the displays off. Note that when the displays are dimmed or turned off, the Standby/On Indicator 1 will remain lit as a reminder that the DPR is still turned on.
Note that all changes to the
In addition to lowering the brightness of the displays or turning them off completely, you may wish to have them appear whenever a button on the remote or front panel is pushed, and then gradually fade out after a set time period. You may do this by making the appropriate settings in the VFD FADE TIME OUT line of the ADVANCED SELECT Menu (Figure 16), as shown on page 37.
Memory Backup
This product is equipped with a memory backup sys- tem that preserves the system configuration information and tuner presets if the unit is accidentally unplugged or subjected to a power outage. This memory will last for at least four weeks, after which time all information must be reentered.
