Check to see if it has been pre-assembled

REMOVE THIS PART IDENTIFICATION

CHART FROM THE MANUAL

This chart is provided to help you identify the small parts used in assembly.		Important: Some parts
may have been pre-assembled for shipping purposes. If you cannot find a part in the parts bags,
check to see if it has been pre-assembled.	The number in parenthesis following each part description
refers to the key number of the part.

Please Note: The assembly is divided into four stages: 1) frame

assembly, 2) arm assembly, 3) cable assembly, and 4) seat assembly. The hardware for each stage is packaged separately. WAIT UNTIL

YOU BEGIN EACH ASSEMBLY STAGE TO OPEN THE PARTS BAG LABELED FOR THAT ASSEMBLY STAGE.

Page 29

Image 29

Healthrider WESY8630C3 manual Check to see if it has been pre-assembled, Refers to the key number of the part

Contents

Model No. WESY8630C3 Serial No QUESTIONS?Serial Number Decal Under Seat Customer HOT Line Limited Warranty Table of Contents Read all instructions in this manual Important PrecautionsSure that the cables are on all of the pulleys Decal shown Before YOU Begin Using the Weider Assembly Frame Assembly BAG TWO Be sure that the pins on Stack of WeightsDo not over Tighten the Nylon Locknut Be sure that the pin Locknuts used in steps 1 through Do not tighten Nylon Locknuts yet Shown Nylon LocknutAs shown Only once Right Arm 5. Be sure that the upperOrder new Retainers Be sure that Onto the Bolt, but do not fully tighten it Identify the Butterfly Cable 89-this is Pulley Plates 31 and 3 1/2 Pulleys PulleyGroove of the Pulley But Bolt, but do not fully tighten it. Leave Shortest CableSure that the Cable Trap is inside Pre-assembled Base 13 with a 3/8 x 2 Bolt 50 and a 3/8 Cable Trap is turned to hold the Cable in place Upper Direction shownPlace Pulley move smoothly Be sure that Large Cable Trap is turned to hold Pivot Identify the High Cable 85-this is 3/8 x 5 Bolt 74 and the 3/8 Nylon LocknutHigh Cable around a 3 1/2 Pulley 82. Attach Bolt 76, a 3/8 Washer 38, and a 3/8 Nylon Locknut Indicated side Nylon Locknut 42. Do not overtighten Be sure that the Cable Trap is in the indi- cated position Seat Plate to the Seat 17 with two 1/4 x 3/4 Screws Press a 1 1/2 Square Inner Cap 57 into the Rear Seat FramePress a 1 1/2 Square Inner Cap 57 into the Leg Lever With the Bolt and a 5/16 Nylon Locknut Press two 3/4 Round Inner Caps 78 into each Pad Tube TROUBLE-SHOOTING and Maintenance on Changing the Weight Setting HOW to USE the Training SystemAttaching the LAT BAR or Nylon Strap to High Pulley Station Attaching the LAT BAR or Nylon Strap to LOW Pulley Station Station Adjusting the LEG Press PlateAttaching and Removing the Seat Attaching the LEG Lever to the LOW Pulley Station Lbs Weight Resistance Chart Tightening the Cables TROUBLE-SHOOTING and MaintenanceSee drawing 1. Remove the 3/8 Nylon Locknut 42 Rear Cable 87 can be tightened in the same manner Long U Bracket Cable DiagramsLow Pulley Butterfly Cable Top Frame High Cable Part No R0600A Ordering Replacement Parts Refers to the key number of the part Check to see if it has been pre-assembled X 3 1/4 Bolt 16 x 1 3/4 Bolt 2 Pulley 82 Not shown to scale 7/8 Plastic Bushing Inner Cap For Future Reference Qty Description R0600A16 x 1 Bolt X 8 Bolt Exploded DRAWING-Model No. WESY8630C3

REMOVE THIS PART IDENTIFICATION

CHART FROM THE MANUAL

check to see if it has been pre-assembled.

refers to the key number of the part.