16 x 1 3/4 Bolt, X 3 1/4 Bolt | Healthrider WESY8630C3 manual

1/4" Washer (37)

5/16" x 1" Bolt (51)

5/16" Washer (20)	1" Retainer (45)	5/16" x 1 3/4" Bolt (68)

3/8" x 2" Bolt (50)

3/8" Washer (38)

5/16" x 2 1/4" Bolt (62)

1/4" Nylon Locknut (44)

5/16" Nylon Locknut (40)	5/16" x 2 1/2" Bolt (39)
5/16" Nylon Locknut (40)
5/16" Nylon Jam Nut (91)	3/8" x 2 1/2" Bolt (65)–1

3/8" Nylon Locknut (42)

5/16" x 2 3/4" Bolt (55)

3/8" Nylon Jam Nut (43)

5/16" x 3" Bolt (92)

1" Tap Screw (72)	3/8" x 3 1/4" Bolt (71)
1/4" x 3/4" Screw (59)	3/8" x 3 1/2" Bolt (66)

Image 30

Healthrider WESY8630C3 manual 16 x 1 3/4 Bolt, X 3 1/4 Bolt

Contents

Serial Number Decal Under Seat QUESTIONS?Model No. WESY8630C3 Serial No Customer HOT Line Table of Contents Limited Warranty Sure that the cables are on all of the pulleys Important PrecautionsRead all instructions in this manual Decal shown Using the Weider Before YOU Begin Assembly Frame Assembly BAG TWO Do not over Tighten the Nylon Locknut Stack of WeightsBe sure that the pins on Be sure that the pin Do not tighten Nylon Locknuts yet Locknuts used in steps 1 through Nylon Locknut As shownShown Order new Retainers Right Arm 5. Be sure that the upperOnly once Be sure that Identify the Butterfly Cable 89-this is Onto the Bolt, but do not fully tighten it Groove of the Pulley PulleyPulley Plates 31 and 3 1/2 Pulleys But Sure that the Cable Trap is inside Shortest CableBolt, but do not fully tighten it. Leave Pre-assembled Cable Trap is turned to hold the Cable in place Base 13 with a 3/8 x 2 Bolt 50 and a 3/8 Direction shown PlaceUpper Be sure that Large Cable Trap is turned to hold Pulley move smoothly High Cable around a 3 1/2 Pulley 82. Attach 3/8 x 5 Bolt 74 and the 3/8 Nylon LocknutPivot Identify the High Cable 85-this is Bolt 76, a 3/8 Washer 38, and a 3/8 Nylon Locknut Nylon Locknut 42. Do not overtighten Indicated side Be sure that the Cable Trap is in the indi- cated position Press a 1 1/2 Square Inner Cap 57 into the Leg Lever Press a 1 1/2 Square Inner Cap 57 into the Rear Seat FrameSeat Plate to the Seat 17 with two 1/4 x 3/4 Screws With the Bolt and a 5/16 Nylon Locknut TROUBLE-SHOOTING and Maintenance on Press two 3/4 Round Inner Caps 78 into each Pad Tube Attaching the LAT BAR or Nylon Strap to High Pulley Station HOW to USE the Training SystemChanging the Weight Setting Attaching the LAT BAR or Nylon Strap to LOW Pulley Station Attaching and Removing the Seat Adjusting the LEG Press PlateStation Attaching the LEG Lever to the LOW Pulley Station Weight Resistance Chart Lbs See drawing 1. Remove the 3/8 Nylon Locknut 42 TROUBLE-SHOOTING and MaintenanceTightening the Cables Rear Cable 87 can be tightened in the same manner Low Pulley Cable DiagramsLong U Bracket Butterfly Cable High Cable Top Frame Ordering Replacement Parts Part No R0600A Check to see if it has been pre-assembled Refers to the key number of the part 16 x 1 3/4 Bolt X 3 1/4 Bolt 2 Pulley 82 Not shown to scale 7/8 Plastic Bushing Inner Cap For Future Reference 16 x 1 Bolt R0600AQty Description X 8 Bolt Exploded DRAWING-Model No. WESY8630C3