Pulley 82 Not shown to scale | Healthrider WESY8630C3 instruction

1/4" x 2" Machine Screw (63)

1/4" x 2" Carriage Bolt (61)

1/4" x 2 1/2" Machine Screw (64)

1/4" x 2 1/2" Carriage Bolt (60)

5/16" x 2 1/2" Carriage Bolt (49)

5/16" x 2 3/4" Carriage Bolt (77)

5/16" x 2" Eyebolt (79)

3/8" x 3 3/4" Bolt (76)

Cable Clip (33)

"V" Pulley (81) (Not shown to scale)

3 1/2" Pulley (82) (Not shown to scale)

3/8" x 2 1/4" Bolt (97)

x 4" Bolt (95)	x 6" Bolt (67)	8" Bolt (52)
3/8"	5/16"	3/8" x

3/8" x 5" Bolt (74)

Page 31

Image 31

Healthrider WESY8630C3 manual Pulley 82 Not shown to scale

Contents

Customer HOT Line QUESTIONS?Model No. WESY8630C3 Serial No Serial Number Decal Under Seat Limited Warranty Table of Contents Decal shown Important PrecautionsRead all instructions in this manual Sure that the cables are on all of the pulleys Before YOU Begin Using the Weider Assembly Frame Assembly BAG TWO Be sure that the pin Stack of WeightsBe sure that the pins on Do not over Tighten the Nylon Locknut Locknuts used in steps 1 through Do not tighten Nylon Locknuts yet As shown Nylon LocknutShown Be sure that Right Arm 5. Be sure that the upperOnly once Order new Retainers Onto the Bolt, but do not fully tighten it Identify the Butterfly Cable 89-this is But PulleyPulley Plates 31 and 3 1/2 Pulleys Groove of the Pulley Pre-assembled Shortest CableBolt, but do not fully tighten it. Leave Sure that the Cable Trap is inside Base 13 with a 3/8 x 2 Bolt 50 and a 3/8 Cable Trap is turned to hold the Cable in place Place Direction shownUpper Pulley move smoothly Be sure that Large Cable Trap is turned to hold Bolt 76, a 3/8 Washer 38, and a 3/8 Nylon Locknut 3/8 x 5 Bolt 74 and the 3/8 Nylon LocknutPivot Identify the High Cable 85-this is High Cable around a 3 1/2 Pulley 82. Attach Indicated side Nylon Locknut 42. Do not overtighten Be sure that the Cable Trap is in the indi- cated position With the Bolt and a 5/16 Nylon Locknut Press a 1 1/2 Square Inner Cap 57 into the Rear Seat FrameSeat Plate to the Seat 17 with two 1/4 x 3/4 Screws Press a 1 1/2 Square Inner Cap 57 into the Leg Lever Press two 3/4 Round Inner Caps 78 into each Pad Tube TROUBLE-SHOOTING and Maintenance on Attaching the LAT BAR or Nylon Strap to LOW Pulley Station HOW to USE the Training SystemChanging the Weight Setting Attaching the LAT BAR or Nylon Strap to High Pulley Station Attaching the LEG Lever to the LOW Pulley Station Adjusting the LEG Press PlateStation Attaching and Removing the Seat Lbs Weight Resistance Chart Rear Cable 87 can be tightened in the same manner TROUBLE-SHOOTING and MaintenanceTightening the Cables See drawing 1. Remove the 3/8 Nylon Locknut 42 Butterfly Cable Cable DiagramsLong U Bracket Low Pulley Top Frame High Cable Part No R0600A Ordering Replacement Parts Refers to the key number of the part Check to see if it has been pre-assembled X 3 1/4 Bolt 16 x 1 3/4 Bolt 2 Pulley 82 Not shown to scale 7/8 Plastic Bushing Inner Cap For Future Reference X 8 Bolt R0600AQty Description 16 x 1 Bolt Exploded DRAWING-Model No. WESY8630C3