Nylon Locknut, As shown, Shown | Healthrider WESY8630C3 guide

FRAME ASSEMBLY

ARM ASSEMBLY

11. Attach the Leg Press Plate (11) to the

Adjustment Tube (10) with a 5/16” x 2 1/2” Bolt (39), two 5/16” Washers (20), and a 5/16”

Nylon Locknut (40).		Be sure that the Leg
Press	Plate and Adjustment Tube are ori-
ented	as shown.

Press a 1 3/4” Square Inner Cap (48) into the

Adjustment Tube (10).

12. Attach the Adjustment Tube (10) to the Leg
Press Arm (9) with the Lock Pin (73).	Be sure
the Leg Press Plate (11) is oriented as
shown.
Press two 2” Square Inner Caps (56) into the
Leg Press Arm (9).

13.Locate and open the parts bag labeled “ARM ASSEMBLY.”

Attach the Leg Press Bumper (53) to the

Front Seat Frame (8) with the 1” Tap Screw (72).

Lubricate the 3/8” x 3 1/4” Bolt (71). Attach the Leg Press Arm (9) to the Press Base (13)

with the Bolt and a 3/8” Nylon Locknut (42).

14.Press a 1” x 7/8” Plastic Bushing (54) onto

each welded spacer on the Press Frame (12). Slide the Press Frame onto the Press Base

(13) so that the Plastic Bushings are aligned

with the indicated tube. Note: This will be a

tight fit. Make sure that the high pulley is on the side shown.

Lubricate the 3/8” x 8” Bolt (52). Attach the Press Frame (12) to the Press Base (13) with

the Bolt and a 3/8” Nylon Locknut (42).

9

11
		10
		40
48		20
48
39
		Angle
		11
12		10
	73	10
	73
		11
		9
		56
13
		8
		9
		53
		42
		72
		71—Lubricate
		13
14
		Tube
High		12
Pulley
Welded		13
Welded
Spacers		52—Lubricate
		52—Lubricate
	42	54
		54

Image 9

Healthrider WESY8630C3 manual Nylon Locknut, As shown, Shown

Contents

Model No. WESY8630C3 Serial No QUESTIONS?Serial Number Decal Under Seat Customer HOT Line Limited Warranty Table of Contents Read all instructions in this manual Important PrecautionsSure that the cables are on all of the pulleys Decal shown Before YOU Begin Using the Weider Assembly Frame Assembly BAG TWO Be sure that the pins on Stack of WeightsDo not over Tighten the Nylon Locknut Be sure that the pin Locknuts used in steps 1 through Do not tighten Nylon Locknuts yet Nylon Locknut As shownShown Only once Right Arm 5. Be sure that the upperOrder new Retainers Be sure that Onto the Bolt, but do not fully tighten it Identify the Butterfly Cable 89-this is Pulley Plates 31 and 3 1/2 Pulleys PulleyGroove of the Pulley But Bolt, but do not fully tighten it. Leave Shortest CableSure that the Cable Trap is inside Pre-assembled Base 13 with a 3/8 x 2 Bolt 50 and a 3/8 Cable Trap is turned to hold the Cable in place Direction shown PlaceUpper Pulley move smoothly Be sure that Large Cable Trap is turned to hold Pivot Identify the High Cable 85-this is 3/8 x 5 Bolt 74 and the 3/8 Nylon LocknutHigh Cable around a 3 1/2 Pulley 82. Attach Bolt 76, a 3/8 Washer 38, and a 3/8 Nylon Locknut Indicated side Nylon Locknut 42. Do not overtighten Be sure that the Cable Trap is in the indi- cated position Seat Plate to the Seat 17 with two 1/4 x 3/4 Screws Press a 1 1/2 Square Inner Cap 57 into the Rear Seat FramePress a 1 1/2 Square Inner Cap 57 into the Leg Lever With the Bolt and a 5/16 Nylon Locknut Press two 3/4 Round Inner Caps 78 into each Pad Tube TROUBLE-SHOOTING and Maintenance on Changing the Weight Setting HOW to USE the Training SystemAttaching the LAT BAR or Nylon Strap to High Pulley Station Attaching the LAT BAR or Nylon Strap to LOW Pulley Station Station Adjusting the LEG Press PlateAttaching and Removing the Seat Attaching the LEG Lever to the LOW Pulley Station Lbs Weight Resistance Chart Tightening the Cables TROUBLE-SHOOTING and MaintenanceSee drawing 1. Remove the 3/8 Nylon Locknut 42 Rear Cable 87 can be tightened in the same manner Long U Bracket Cable DiagramsLow Pulley Butterfly Cable Top Frame High Cable Part No R0600A Ordering Replacement Parts Refers to the key number of the part Check to see if it has been pre-assembled X 3 1/4 Bolt 16 x 1 3/4 Bolt 2 Pulley 82 Not shown to scale 7/8 Plastic Bushing Inner Cap For Future Reference Qty Description R0600A16 x 1 Bolt X 8 Bolt Exploded DRAWING-Model No. WESY8630C3