7/8 Plastic Bushing Inner Cap | Healthrider WESY8630C3 specification

1" x 7/8" Plastic Bushing (54)

1" Inner Cap (98)

1" Round Inner Cap (70)

1 1/8" x 2 1/2" Plastic Bushing (47)

1 1/2" Square Inner Cap (57)

1/2" x 3/4" Spacer (69)

1" Round Outer Cap (46)

3/4" Round Inner Cap (78)

1 3/4" Square Inner Cap (48)

2" Square Outer Cap (58)

2" Square Inner Cap (56)

Page 32

Image 32

Healthrider WESY8630C3 manual 7/8 Plastic Bushing Inner Cap

Contents

QUESTIONS? Model No. WESY8630C3 Serial NoSerial Number Decal Under Seat Customer HOT Line Table of Contents Limited Warranty Important Precautions Read all instructions in this manualSure that the cables are on all of the pulleys Decal shown Using the Weider Before YOU Begin Assembly Frame Assembly BAG TWO Stack of Weights Be sure that the pins onDo not over Tighten the Nylon Locknut Be sure that the pin Do not tighten Nylon Locknuts yet Locknuts used in steps 1 through Shown Nylon LocknutAs shown Right Arm 5. Be sure that the upper Only onceOrder new Retainers Be sure that Identify the Butterfly Cable 89-this is Onto the Bolt, but do not fully tighten it Pulley Pulley Plates 31 and 3 1/2 PulleysGroove of the Pulley But Shortest Cable Bolt, but do not fully tighten it. LeaveSure that the Cable Trap is inside Pre-assembled Cable Trap is turned to hold the Cable in place Base 13 with a 3/8 x 2 Bolt 50 and a 3/8 Upper Direction shownPlace Be sure that Large Cable Trap is turned to hold Pulley move smoothly 3/8 x 5 Bolt 74 and the 3/8 Nylon Locknut Pivot Identify the High Cable 85-this isHigh Cable around a 3 1/2 Pulley 82. Attach Bolt 76, a 3/8 Washer 38, and a 3/8 Nylon Locknut Nylon Locknut 42. Do not overtighten Indicated side Be sure that the Cable Trap is in the indi- cated position Press a 1 1/2 Square Inner Cap 57 into the Rear Seat Frame Seat Plate to the Seat 17 with two 1/4 x 3/4 ScrewsPress a 1 1/2 Square Inner Cap 57 into the Leg Lever With the Bolt and a 5/16 Nylon Locknut TROUBLE-SHOOTING and Maintenance on Press two 3/4 Round Inner Caps 78 into each Pad Tube HOW to USE the Training System Changing the Weight SettingAttaching the LAT BAR or Nylon Strap to High Pulley Station Attaching the LAT BAR or Nylon Strap to LOW Pulley Station Adjusting the LEG Press Plate StationAttaching and Removing the Seat Attaching the LEG Lever to the LOW Pulley Station Weight Resistance Chart Lbs TROUBLE-SHOOTING and Maintenance Tightening the CablesSee drawing 1. Remove the 3/8 Nylon Locknut 42 Rear Cable 87 can be tightened in the same manner Cable Diagrams Long U BracketLow Pulley Butterfly Cable High Cable Top Frame Ordering Replacement Parts Part No R0600A Check to see if it has been pre-assembled Refers to the key number of the part 16 x 1 3/4 Bolt X 3 1/4 Bolt 2 Pulley 82 Not shown to scale 7/8 Plastic Bushing Inner Cap For Future Reference R0600A Qty Description16 x 1 Bolt X 8 Bolt Exploded DRAWING-Model No. WESY8630C3