6Mobile Home | Hearth and Home Technologies CB1200-B instruction

R

CB 1200 Pellet Stove

6Mobile Home

A. Mobile Home Installation

You must use a Quadra-Fire Outside Air Kit for installation in a mobile home.

1.An outside air inlet must be provided for the combustion air and must remain clear of leaves, debris, ice and/or snow. It must be unrestricted while the appliance is in use to prevent room air starvation which causes smoke spillage. Smoke spillage can also set off smoke alarms.

CAUTION

Maintain structural integrity of mobile home:

•Floor, wall, ceiling and/or roof. Do NOT cut through:

•Floor joist, wall, studs or ceiling trusses.

•Any supporting material that would affect the structural integrity.

2.The combustion air duct system must be made of metal. It must permit zero clearance to combustible construction and prevent material from dropping into the inlet or into the area beneath the dwelling and contain a rodent screen.

3.The appliance must be secured to the mobile home structure by bolting it to the ﬂoor (using lag bolts). Use the same holes that secured the appliance to the shipping pallet.

4.The appliance must be grounded with #8 solid copper grounding wire or equivalent, terminated at each end with an NEC approved grounding device.

5.Refer to Clearances to Combustibles and ﬂoor pro- tection requirements on pages 8 & 9 for listings to combustibles and appropriate chimney systems.

6.Use silicone to create an effective vapor barrier at the location where the chimney or other component penetrates to the the exterior of the structure.

7.Follow the chimney manufacturer’s instructions when installing the vent system for use in a mobile home.

8.Installation shall be in accordance with the Manufactur- ers Home & Safety Standard (HUD) CFR 3280, Part 24.

WARNING

Installation must comply with Manufactured Home and Safety Standard (HUD), CFR 3280, Part 24.

CAUTION

Never draw outside combustion air from:

•Wall, ﬂoor or ceiling cavity

•Enclosed space such as an attic or garage

Spark Arrestor Cap

Storm Collar

Roof Flashing

Joist Shield/Firestop

Approved Class “L” o

“PL” Pellet Vent

Figure 16.1

WARNING

Never install in a sleeping room.

Page 16

7014-082D

September 1, 2008

Image 16

Hearth and Home Technologies CB1200-B owner manual 6Mobile Home

Contents

Classic BAY 1200 Pellet Stove Hot glass will cause burns CB 1200 Pellet Stove Testing Lab & Report Number Serial Number Model Mfg DateBehind left side curtain on outside of hopper wall Table of Contents Listing and Code Approvals Design, Installation & Location Considerations Fire SafetyGetting Started Appliance Location CB 1200 Pellet Stove Tools And Supplies Needed Inspect Appliance & Components and Pre-Use Check List 3Dimensions and Clearances Appliance Dimensions CB 1200 Pellet Stove Clearances to Combustibles UL and ULC CB 1200 Pellet Stove Hearth Pad Requirements UL and ULC Exception for Horizontal InstallationsHearth Pad Requirements 4Vent Information Pipe Selection Chart CB 1200 Pellet Stove Equivalent Feet of PipeExample of 3 Elbow-Rear Vent Termination Calculaton Example 5Venting Systems Alcove Degree Straight OutCB 1200 Pellet Stove Through The Wall CB 1200 Pellet Stove Vertical Through The Wall & Vertical Masonry Alternate Masonry 6Mobile Home 7Appliance Set-Up Rear Installation Floor InstallationOutside Air Kit Instructions CB 1200 Pellet Stove Top Vent Adapter Installation Rear Vent and Rear Vent to Top Vent Adapter InstallationInstalling the Top Vent Adapter See Figure Installed Clip Installing Logo Nickel Only Charred Areas in the BackTop Log, Left Right CB 1200 Pellet Stove Door Installation Thermostat InstallationTo install door To adjust latches 8Operating Instructions Fuel Size And Material General Operating Information Feed Rate Adjustment Instructions Starting Your First Fire Button. See .1, page 22 . When you press Frequently Asked QuestionsCB 1200 Pellet Stove Ignition Cycles Symptom TroubleshootingPossible Cause Corrective Action Page Page Quick Reference Maintenance Chart Cleaning or Inspection10Maintaining & Servicing Your Appliance Frequency Daily Weekly Monthly Yearly Cleaning Firepot with Cleaning Rod & Firepot Scraper Cleaning Ash PanCleaning Heat Exchanger Chambers & Drop Tube Ash Removal from Firebox Cleaning Beneath Heat Exchanger Door Latch Inspection Cleaning Exhaust PathCleaning the Hopper Cleaning the Glass Cleaning Exhaust Blower Requires No Lubrication Cleaning the Top Vent Adapter Preparing Firebox for Non-Burn Season Frequency Yearly CB 1200 Pellet Stove High Ash Fuel Content Maintenance Convection Blower Replacement Install new blower Exhaust Blower Replacement Remove existing blowerRe-install blower to blower housing Glass Replacement Replacing Side Glass Screws Reference Materials Component Function & Location Vacuum Switch Wiring Harness See .1 belowSnap Disc #1 Convection Blower 145F Snap Disc #2 Thermostat Override 200F CB 1200 Pellet Stove Component Locations Glass Size Center 13-7/8 wide x 11 high CB 1200 Pellet Stove Exploded ViewsGlass Size Sides 8 wide x 11 high Nbr Description CB 1200 Pellet Stove CB 1200 Pellet Stove Service Parts and Accessories Item # Parts Alphabetical Order Item # Service Parts Alphabetical Order Accessories Appliance CB 1200 Pellet Stove Service And Maintenance Log Date of Service Performed By Description of Service CB 1200 Pellet Stove Homeowner’s Notes CB 1200 Pellet Stove Warranty Policy CONDITIONS, Exclusions & Limitation of Liability Hearth & Home Technologies Limited Warranty Cont’d Contact Information