Manuals / Hearth and Home Technologies / Household Appliance / Indoor Fireplace

Hearth and Home Technologies CNXT4842IT, CNXT4842ILT, CNXT4842IH Lighting Instructions IPI

Models: CNXT4236ILH CNXT4236IH CNXT4842IH CNXT4842ILT CNXT4236ILT CNXT4842IT CNXT4236IT CNXT4842ILH

1 80

Download 80 pages 27 Kb

Page 11

I. Lighting Instructions (IPI)

•For normal use, activate/deactivate your ﬁreplace with the wall switch or remote control.

•The IPI system may be operated with two D-cell batteries. When using batteries, unplug the transformer. To prolong battery life, remove them when using the transformer.

•If your ﬁreplace must be deactivated for service or an extended period of time, follow the instructions below.

Heatilator • Caliber CNXT Series • 4047-132 Rev U • 11/08

11

Image 11

Hearth and Home Technologies CNXT4842IT, CNXT4842ILT, CNXT4842IH, CNXT4842ILH, CNXT4236ILH Lighting Instructions IPI

Contents

What to do if you smell gas Installation and OperationModels Direct Vent Gas Appliance Homeowner Reference Information Congratulations User Guide Table of ContentsInstaller Guide Reference Materials Appliance SetupTroubleshooting Finishing CONDITIONS, Exclusions & Limitation of Liability Warranty Hearth & Home Technologies Limited Warranty Warranty Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Your Fireplace Gas Fireplace SafetyOperating Instructions Clear Space Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Fan Kit optional Lighting Instructions IPI After Fireplace is Lit Frequently Asked Questions Maintenance Tasks-Homeowner Maintenance and Service Maintenance Tasks-Qualiﬁed Service Technician Typical Appliance System Getting Started Any such action may cause a ﬁre hazard Design and Installation ConsiderationsTools and Supplies Needed Inspect Appliance and Components Model # Framing and ClearancesSelecting Appliance Location Rough Opening Model Width Height Depth Constructing the Appliance ChaseClearances Mantel Legs or Wall Projections Mantel and Wall ProjectionsMantels Vent Termination Minimum Clearances Termination Locations Minimum Clearances for Termination Use of Elbows Vent Information and DiagramsApproved Pipe Vent Table Key One Elbow Vent DiagramsTop Vent Horizontal Termination Min Max +H 2 max +H 2+H 3 max Two 45 Elbows replacing One 90 ElbowTwo Elbows Three Elbows Installed Vertically No Elbow Top Vent Vertical Termination 12 ft 3.66 m min 60 ft 18.29 m max One 45 Elbow Rear Vent Horizontal Termination Two Elbows Rear Vent Vertical Termination Min Ft 1.83 m max 12 ft 3.66 m min 60 ft 18.29 m max 17 Flat Bafﬂe Installing Vertical Termination Bafﬂe Replace the glass refer to .H Start the appliance Combustible Wall Penetration Vent Clearances and FramingPipe Clearances to Combustibles Wall Penetration Framing Installing Ceiling Firestop Install the Ceiling Firestop Vaulted Ceiling Installation Install Attic Insulation ShieldFlat Ceiling Installation Convert from Top Vent to Rear Vent Appliance Preparation Outer Collar, Remove Four Screws 11 Place Outer Collar on Rear of Appliance 16 Cover Plate-Replace 20 Proper Positioning, Leveling And Securing Of An Securing and Leveling the Appliance Assemble Pipe Sections DVP Only Installing Vent PipeAttach Pipe to the Firebox Assembly Assemble Pipe Sections DVP Only Adding Venting Components Assemble Vent Sections SLP Only Secure the Vent Sections Assemble Slip Sections Disassemble Vent Sections Install Decorative Ceiling Components SLP only Caulk Install Metal Roof Flashing 17 Assembling the Storm Collar Assemble and Install Storm Collar SLP-FS Install RF4-8 Heat Shield Requirements for Horizontal Termination Installing Vertical Termination CapInstalling Decorative Wall Components SLP only Interior Install Horizontal Termination Cap Gas Connection Gas InformationFuel Conversion Gas Pressure Electrical Information Wiring RequirementsIntelliﬁre Ignition System Wiring Electrical Service and Repair Junction Box Installation Determine Location WSK-MLT Multifunction Wall SwitchPrecautions Intelliﬁre IPI Wiring Diagram Wiring the Wall Switch Hook up the Temperature Sensor Switch for Fan Install the Flame Solenoid Install the Cover Plate Install the Remote Cover Plate WSK-MLT Operating Instructions Setting Flame Height/Manifold PressureWall Switch Button Operation Service Parts List Facing Material Finishing Appliance Setup Place the Rockwool Log Assembly Removing Fixed Glass Assembly Install Trim and/or SurroundsInstall Hood Air Shutter Setting Intelliﬁre Ignition System TroubleshootingSymptom Possible Cause Corrective Action Will not ignite. If the pilot Reference Materials Appliance Dimension Diagram DVP Vent Components Vent Components Diagrams BEK DVP-BEK2 DVP-TVHW Horizontal Termination Cap DVP-TRAP DVP-HRC-SS Effective Adapter SL-2DVP Parts Service Stocked Service Parts IPI Valve Assembly CNXT4842 Series Log/Grate Assembly Valve Assembly Model Description Optional Components Contact Information