Manuals / Hearth and Home Technologies / Household Appliance / Indoor Fireplace

Hearth and Home Technologies CNXT4842ILH, CNXT4842ILT Top Vent Vertical Termination, No Elbow

Models: CNXT4236ILH CNXT4236IH CNXT4842IH CNXT4842ILT CNXT4236ILT CNXT4842IT CNXT4236IT CNXT4842ILH

1 80

Download 80 pages 27 Kb

Page 26

Image 26

2. Top Vent - Vertical Termination

No Elbow

12 ft (3.66 m) min.

60 ft (18.29 m) max.

Figure 7.7

Two Elbows

12 ft (3.66 m) min.

60 ft (18.29 m) max.

Maximum horizontal run is 100% of vertical, but cannot exceed 26 ft (7.92 m)

Figure 7.8

Note: If installing a vertical vent/ termination off the top of the appli- ance, the vertical termination bafﬂe should be used.

Note: If installing a vertical vent/ termination off the top of the appli- ance, the vertical termination bafﬂe should be used.

26	Heatilator • Caliber CNXT Series • 4047-132 Rev U • 11/08

Image 26

Hearth and Home Technologies CNXT4842ILH, CNXT4842ILT, CNXT4842IH, CNXT4842IT Top Vent Vertical Termination, No Elbow

Contents

Direct Vent Gas Appliance Installation and OperationModels What to do if you smell gas Congratulations Homeowner Reference Information User Guide Table of ContentsInstaller Guide Finishing Appliance SetupTroubleshooting Reference Materials Warranty Hearth & Home Technologies Limited Warranty CONDITIONS, Exclusions & Limitation of Liability Warranty Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Your Fireplace Gas Fireplace SafetyOperating Instructions Fan Kit optional Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Clear Space Lighting Instructions IPI Frequently Asked Questions After Fireplace is Lit Maintenance and Service Maintenance Tasks-Homeowner Maintenance Tasks-Qualiﬁed Service Technician Getting Started Typical Appliance System Inspect Appliance and Components Design and Installation ConsiderationsTools and Supplies Needed Any such action may cause a ﬁre hazard Model # Framing and ClearancesSelecting Appliance Location Rough Opening Model Width Height Depth Constructing the Appliance ChaseClearances Mantel Legs or Wall Projections Mantel and Wall ProjectionsMantels Termination Locations Vent Termination Minimum Clearances Minimum Clearances for Termination Vent Table Key Vent Information and DiagramsApproved Pipe Use of Elbows One Elbow Vent DiagramsTop Vent Horizontal Termination Min Max +H 2 max +H 2+H 3 max Two 45 Elbows replacing One 90 ElbowTwo Elbows Installed Vertically Three Elbows Top Vent Vertical Termination No Elbow 12 ft 3.66 m min 60 ft 18.29 m max Rear Vent Horizontal Termination One 45 Elbow Two Elbows Rear Vent Vertical Termination Min Ft 1.83 m max 12 ft 3.66 m min 60 ft 18.29 m max Installing Vertical Termination Bafﬂe 17 Flat Bafﬂe Replace the glass refer to .H Start the appliance Wall Penetration Framing Vent Clearances and FramingPipe Clearances to Combustibles Combustible Wall Penetration Install the Ceiling Firestop Installing Ceiling Firestop Vaulted Ceiling Installation Install Attic Insulation ShieldFlat Ceiling Installation Appliance Preparation Convert from Top Vent to Rear Vent Outer Collar, Remove Four Screws 11 Place Outer Collar on Rear of Appliance 16 Cover Plate-Replace Securing and Leveling the Appliance 20 Proper Positioning, Leveling And Securing Of An Assemble Pipe Sections DVP Only Installing Vent PipeAttach Pipe to the Firebox Assembly Assemble Pipe Sections DVP Only Assemble Vent Sections SLP Only Adding Venting Components Assemble Slip Sections Secure the Vent Sections Install Decorative Ceiling Components SLP only Disassemble Vent Sections Install Metal Roof Flashing Caulk Assemble and Install Storm Collar 17 Assembling the Storm Collar Install RF4-8 SLP-FS Heat Shield Requirements for Horizontal Termination Installing Vertical Termination CapInstalling Decorative Wall Components SLP only Install Horizontal Termination Cap Interior Gas Pressure Gas InformationFuel Conversion Gas Connection Electrical Service and Repair Junction Box Installation Wiring RequirementsIntelliﬁre Ignition System Wiring Electrical Information Determine Location WSK-MLT Multifunction Wall SwitchPrecautions Wiring the Wall Switch Intelliﬁre IPI Wiring Diagram Install the Flame Solenoid Hook up the Temperature Sensor Switch for Fan Install the Remote Cover Plate Install the Cover Plate WSK-MLT Operating Instructions Setting Flame Height/Manifold PressureWall Switch Button Operation Service Parts List Finishing Facing Material Appliance Setup Log Assembly Place the Rockwool Air Shutter Setting Install Trim and/or SurroundsInstall Hood Removing Fixed Glass Assembly Intelliﬁre Ignition System TroubleshootingSymptom Possible Cause Corrective Action Will not ignite. If the pilot Appliance Dimension Diagram Reference Materials Vent Components Diagrams DVP Vent Components BEK DVP-BEK2 DVP-TVHW DVP-TRAP Horizontal Termination Cap DVP-HRC-SS Effective SL-2DVP Adapter Service Parts Service Parts Stocked IPI Valve Assembly CNXT4842 Series Log/Grate Assembly Valve Assembly Optional Components Model Description Contact Information