Manuals / Hearth and Home Technologies / Household Appliance / Indoor Fireplace

Hearth and Home Technologies CNXT4842ILT, CNXT4842IH, CNXT4842ILH, CNXT4842IT SL-2DVP, Adapter

Models: CNXT4236ILH CNXT4236IH CNXT4842IH CNXT4842ILT CNXT4236ILT CNXT4842IT CNXT4236IT CNXT4842ILH

1 80

Download 80 pages 27 Kb

Page 72

B. Vent Components Diagrams (continued)

SLK-SNKD	SLP-CCS-BK
Snorkel	Cathedral Ceiling Sup-
Termination Cap	port Box-Black

DVP-FBHT

Firebrick Termination Cap

(This termination cap requires an SL-2DVP adapter when used with SLP Pipe)

SLP-TRAP1

Horizontal

Termination Cap

SLP-TRAP2

Horizontal

Termination Cap

Figure 16.8 SLP Series Vent Components

SLP-TVHW
Vertical	PVK-80
Termination Cap	Power Vent

SL-2DVP

Adapter

8-1/8 in.				13 in.
(206 mm)				(330 mm)
(206 mm)				(330 mm)

15in.

(381 mm)

SLP-HRC-SS

Effective Length
Effective Length			5-1/2 in.			8-3/8 in.
5-3/4 to 8-3/8 in.			5-1/2 in.			8-3/8 in.
146 to 213 mm			140 mm			213 mm
146 to 213 mm			140 mm			213 mm
			87°		3°

10-1/2 in.

267 mm

10-7/8 in.

276 mm

SLP-HRC-ZC-SS

72	Heatilator • Caliber CNXT Series • 4047-132 Rev U • 11/08

Image 72

Hearth and Home Technologies CNXT4842ILT, CNXT4842IH, CNXT4842ILH, CNXT4842IT, CNXT4236ILH, CNXT4236ILT SL-2DVP, Adapter

Contents

Installation and Operation ModelsDirect Vent Gas Appliance What to do if you smell gas Congratulations Homeowner Reference Information Table of Contents Installer GuideUser Guide Appliance Setup TroubleshootingFinishing Reference Materials Warranty Hearth & Home Technologies Limited Warranty CONDITIONS, Exclusions & Limitation of Liability Warranty Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Gas Fireplace Safety Operating InstructionsYour Fireplace Fixed Glass Assembly Remote Controls, Wall Controls and Wall SwitchesFan Kit optional Clear Space Lighting Instructions IPI Frequently Asked Questions After Fireplace is Lit Maintenance and Service Maintenance Tasks-Homeowner Maintenance Tasks-Qualiﬁed Service Technician Getting Started Typical Appliance System Design and Installation Considerations Tools and Supplies NeededInspect Appliance and Components Any such action may cause a ﬁre hazard Framing and Clearances Selecting Appliance LocationModel # Constructing the Appliance Chase ClearancesRough Opening Model Width Height Depth Mantel and Wall Projections MantelsMantel Legs or Wall Projections Termination Locations Vent Termination Minimum Clearances Minimum Clearances for Termination Vent Information and Diagrams Approved PipeVent Table Key Use of Elbows Vent Diagrams Top Vent Horizontal TerminationOne Elbow Two 45 Elbows replacing One 90 Elbow Two ElbowsMin Max +H 2 max +H 2+H 3 max Installed Vertically Three Elbows Top Vent Vertical Termination No Elbow 12 ft 3.66 m min 60 ft 18.29 m max Rear Vent Horizontal Termination One 45 Elbow Two Elbows Rear Vent Vertical Termination Min Ft 1.83 m max 12 ft 3.66 m min 60 ft 18.29 m max Installing Vertical Termination Bafﬂe 17 Flat Bafﬂe Replace the glass refer to .H Start the appliance Vent Clearances and Framing Pipe Clearances to CombustiblesWall Penetration Framing Combustible Wall Penetration Install the Ceiling Firestop Installing Ceiling Firestop Install Attic Insulation Shield Flat Ceiling InstallationVaulted Ceiling Installation Appliance Preparation Convert from Top Vent to Rear Vent Outer Collar, Remove Four Screws 11 Place Outer Collar on Rear of Appliance 16 Cover Plate-Replace Securing and Leveling the Appliance 20 Proper Positioning, Leveling And Securing Of An Installing Vent Pipe Attach Pipe to the Firebox AssemblyAssemble Pipe Sections DVP Only Assemble Pipe Sections DVP Only Assemble Vent Sections SLP Only Adding Venting Components Assemble Slip Sections Secure the Vent Sections Install Decorative Ceiling Components SLP only Disassemble Vent Sections Install Metal Roof Flashing Caulk Assemble and Install Storm Collar 17 Assembling the Storm Collar Install RF4-8 SLP-FS Installing Vertical Termination Cap Installing Decorative Wall Components SLP onlyHeat Shield Requirements for Horizontal Termination Install Horizontal Termination Cap Interior Gas Information Fuel ConversionGas Pressure Gas Connection Wiring Requirements Intelliﬁre Ignition System WiringElectrical Service and Repair Junction Box Installation Electrical Information WSK-MLT Multifunction Wall Switch PrecautionsDetermine Location Wiring the Wall Switch Intelliﬁre IPI Wiring Diagram Install the Flame Solenoid Hook up the Temperature Sensor Switch for Fan Install the Remote Cover Plate Install the Cover Plate Setting Flame Height/Manifold Pressure Wall Switch Button OperationWSK-MLT Operating Instructions Service Parts List Finishing Facing Material Appliance Setup Log Assembly Place the Rockwool Install Trim and/or Surrounds Install HoodAir Shutter Setting Removing Fixed Glass Assembly Troubleshooting Symptom Possible Cause Corrective ActionIntelliﬁre Ignition System Will not ignite. If the pilot Appliance Dimension Diagram Reference Materials Vent Components Diagrams DVP Vent Components BEK DVP-BEK2 DVP-TVHW DVP-TRAP Horizontal Termination Cap DVP-HRC-SS Effective SL-2DVP Adapter Service Parts Service Parts Stocked IPI Valve Assembly CNXT4842 Series Log/Grate Assembly Valve Assembly Optional Components Model Description Contact Information