Manuals / Hearth and Home Technologies / Household Appliance / Indoor Fireplace

Hearth and Home Technologies CNXT4236ILH, CNXT4842ILT Finishing, Appliance Setup, Troubleshooting

Models: CNXT4236ILH CNXT4236IH CNXT4842IH CNXT4842ILT CNXT4236ILT CNXT4842IT CNXT4236IT CNXT4842ILH

1 80

Download 80 pages 27 Kb

Page 4

13 Finishing

A.	Mantel and Wall Projections	59
B.	Facing Material	59

14 Appliance Setup

A.	Remove Glass Assembly	60
B.	Remove the Shipping Materials	60
C.	Clean the Appliance	60
D.	Accessories	60
E.	Heat-Zone-Gas	60
F.	Lava Rock, Vermiculite, Rockwool Placement	60
G.	Log Assembly	61
H.	Fixed Glass Assembly	62
I.	Install Trim and/or Surrounds	62
J.	Install Hood	62
K.	Air Shutter Setting	62

15	Troubleshooting
	A.	Intelliﬁre Ignition System	63
16	Reference Materials
	A.	Appliance Dimension Diagram	65
	B.	Vent Components Diagrams	66
	C.	Service Parts	73
	D.	Optional Components	79
	E.	Contact Information	80

= Contains updated information.

4	Heatilator • Caliber CNXT Series • 4047-132 Rev U • 11/08

Image 4

Hearth and Home Technologies CNXT4236ILH, CNXT4842ILT Finishing, Appliance Setup, Troubleshooting, Reference Materials

Contents

Installation and Operation ModelsDirect Vent Gas Appliance What to do if you smell gas Congratulations Homeowner Reference Information Installer Guide Table of ContentsUser Guide Appliance Setup TroubleshootingFinishing Reference Materials Warranty Hearth & Home Technologies Limited Warranty CONDITIONS, Exclusions & Limitation of Liability Warranty Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Operating Instructions Gas Fireplace SafetyYour Fireplace Fixed Glass Assembly Remote Controls, Wall Controls and Wall SwitchesFan Kit optional Clear Space Lighting Instructions IPI Frequently Asked Questions After Fireplace is Lit Maintenance and Service Maintenance Tasks-Homeowner Maintenance Tasks-Qualiﬁed Service Technician Getting Started Typical Appliance System Design and Installation Considerations Tools and Supplies NeededInspect Appliance and Components Any such action may cause a ﬁre hazard Selecting Appliance Location Framing and ClearancesModel # Clearances Constructing the Appliance ChaseRough Opening Model Width Height Depth Mantels Mantel and Wall ProjectionsMantel Legs or Wall Projections Termination Locations Vent Termination Minimum Clearances Minimum Clearances for Termination Vent Information and Diagrams Approved PipeVent Table Key Use of Elbows Top Vent Horizontal Termination Vent DiagramsOne Elbow Two Elbows Two 45 Elbows replacing One 90 ElbowMin Max +H 2 max +H 2+H 3 max Installed Vertically Three Elbows Top Vent Vertical Termination No Elbow 12 ft 3.66 m min 60 ft 18.29 m max Rear Vent Horizontal Termination One 45 Elbow Two Elbows Rear Vent Vertical Termination Min Ft 1.83 m max 12 ft 3.66 m min 60 ft 18.29 m max Installing Vertical Termination Bafﬂe 17 Flat Bafﬂe Replace the glass refer to .H Start the appliance Vent Clearances and Framing Pipe Clearances to CombustiblesWall Penetration Framing Combustible Wall Penetration Install the Ceiling Firestop Installing Ceiling Firestop Flat Ceiling Installation Install Attic Insulation ShieldVaulted Ceiling Installation Appliance Preparation Convert from Top Vent to Rear Vent Outer Collar, Remove Four Screws 11 Place Outer Collar on Rear of Appliance 16 Cover Plate-Replace Securing and Leveling the Appliance 20 Proper Positioning, Leveling And Securing Of An Installing Vent Pipe Attach Pipe to the Firebox AssemblyAssemble Pipe Sections DVP Only Assemble Pipe Sections DVP Only Assemble Vent Sections SLP Only Adding Venting Components Assemble Slip Sections Secure the Vent Sections Install Decorative Ceiling Components SLP only Disassemble Vent Sections Install Metal Roof Flashing Caulk Assemble and Install Storm Collar 17 Assembling the Storm Collar Install RF4-8 SLP-FS Installing Decorative Wall Components SLP only Installing Vertical Termination CapHeat Shield Requirements for Horizontal Termination Install Horizontal Termination Cap Interior Gas Information Fuel ConversionGas Pressure Gas Connection Wiring Requirements Intelliﬁre Ignition System WiringElectrical Service and Repair Junction Box Installation Electrical Information Precautions WSK-MLT Multifunction Wall SwitchDetermine Location Wiring the Wall Switch Intelliﬁre IPI Wiring Diagram Install the Flame Solenoid Hook up the Temperature Sensor Switch for Fan Install the Remote Cover Plate Install the Cover Plate Wall Switch Button Operation Setting Flame Height/Manifold PressureWSK-MLT Operating Instructions Service Parts List Finishing Facing Material Appliance Setup Log Assembly Place the Rockwool Install Trim and/or Surrounds Install HoodAir Shutter Setting Removing Fixed Glass Assembly Symptom Possible Cause Corrective Action TroubleshootingIntelliﬁre Ignition System Will not ignite. If the pilot Appliance Dimension Diagram Reference Materials Vent Components Diagrams DVP Vent Components BEK DVP-BEK2 DVP-TVHW DVP-TRAP Horizontal Termination Cap DVP-HRC-SS Effective SL-2DVP Adapter Service Parts Service Parts Stocked IPI Valve Assembly CNXT4842 Series Log/Grate Assembly Valve Assembly Optional Components Model Description Contact Information