Manuals / Hearth and Home Technologies / Household Appliance / Indoor Fireplace

Hearth and Home Technologies CNXT4236IT, CNXT4842ILT, CNXT4842IH, CNXT4842ILH, CNXT4842IT Dvp-Hrc-Ss

Models: CNXT4236ILH CNXT4236IH CNXT4842IH CNXT4842ILT CNXT4236ILT CNXT4842IT CNXT4236IT CNXT4842ILH

1 80

Download 80 pages 27 Kb

Page 70

B. Vent Components Diagrams (continued)

Fillers

DVP-TRAP to DVP-HPC Side Filler Kit

8-1/8 in.

(206 mm)

15in.

(381 mm)

13in.

(330 mm)

DVP-HRC-SS

Effective Length 5-3/4 to 8-3/8 in. 146 to 213 mm

	5-1/2 in.		8-3/8 in.
	140 mm		213 mm

	87°	3°

10-1/2 in.

267 mm

10-7/8 in.

276 mm

DVP-HRC-ZC-SS

Figure 16.6 DVP Vent Components

70	Heatilator • Caliber CNXT Series • 4047-132 Rev U • 11/08

Image 70

Hearth and Home Technologies CNXT4236IT, CNXT4842ILT, CNXT4842IH, CNXT4842ILH, CNXT4842IT, CNXT4236ILH, CNXT4236ILT Dvp-Hrc-Ss

Contents

Direct Vent Gas Appliance Installation and OperationModels What to do if you smell gas Congratulations Homeowner Reference Information Installer Guide Table of ContentsUser Guide Finishing Appliance SetupTroubleshooting Reference Materials Warranty Hearth & Home Technologies Limited Warranty CONDITIONS, Exclusions & Limitation of Liability Warranty Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Operating Instructions Gas Fireplace SafetyYour Fireplace Fan Kit optional Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Clear Space Lighting Instructions IPI Frequently Asked Questions After Fireplace is Lit Maintenance and Service Maintenance Tasks-Homeowner Maintenance Tasks-Qualiﬁed Service Technician Getting Started Typical Appliance System Inspect Appliance and Components Design and Installation ConsiderationsTools and Supplies Needed Any such action may cause a ﬁre hazard Selecting Appliance Location Framing and ClearancesModel # Clearances Constructing the Appliance ChaseRough Opening Model Width Height Depth Mantels Mantel and Wall ProjectionsMantel Legs or Wall Projections Termination Locations Vent Termination Minimum Clearances Minimum Clearances for Termination Vent Table Key Vent Information and DiagramsApproved Pipe Use of Elbows Top Vent Horizontal Termination Vent DiagramsOne Elbow Two Elbows Two 45 Elbows replacing One 90 ElbowMin Max +H 2 max +H 2+H 3 max Installed Vertically Three Elbows Top Vent Vertical Termination No Elbow 12 ft 3.66 m min 60 ft 18.29 m max Rear Vent Horizontal Termination One 45 Elbow Two Elbows Rear Vent Vertical Termination Min Ft 1.83 m max 12 ft 3.66 m min 60 ft 18.29 m max Installing Vertical Termination Bafﬂe 17 Flat Bafﬂe Replace the glass refer to .H Start the appliance Wall Penetration Framing Vent Clearances and FramingPipe Clearances to Combustibles Combustible Wall Penetration Install the Ceiling Firestop Installing Ceiling Firestop Flat Ceiling Installation Install Attic Insulation ShieldVaulted Ceiling Installation Appliance Preparation Convert from Top Vent to Rear Vent Outer Collar, Remove Four Screws 11 Place Outer Collar on Rear of Appliance 16 Cover Plate-Replace Securing and Leveling the Appliance 20 Proper Positioning, Leveling And Securing Of An Assemble Pipe Sections DVP Only Installing Vent PipeAttach Pipe to the Firebox Assembly Assemble Pipe Sections DVP Only Assemble Vent Sections SLP Only Adding Venting Components Assemble Slip Sections Secure the Vent Sections Install Decorative Ceiling Components SLP only Disassemble Vent Sections Install Metal Roof Flashing Caulk Assemble and Install Storm Collar 17 Assembling the Storm Collar Install RF4-8 SLP-FS Installing Decorative Wall Components SLP only Installing Vertical Termination CapHeat Shield Requirements for Horizontal Termination Install Horizontal Termination Cap Interior Gas Pressure Gas InformationFuel Conversion Gas Connection Electrical Service and Repair Junction Box Installation Wiring RequirementsIntelliﬁre Ignition System Wiring Electrical Information Precautions WSK-MLT Multifunction Wall SwitchDetermine Location Wiring the Wall Switch Intelliﬁre IPI Wiring Diagram Install the Flame Solenoid Hook up the Temperature Sensor Switch for Fan Install the Remote Cover Plate Install the Cover Plate Wall Switch Button Operation Setting Flame Height/Manifold PressureWSK-MLT Operating Instructions Service Parts List Finishing Facing Material Appliance Setup Log Assembly Place the Rockwool Air Shutter Setting Install Trim and/or SurroundsInstall Hood Removing Fixed Glass Assembly Symptom Possible Cause Corrective Action TroubleshootingIntelliﬁre Ignition System Will not ignite. If the pilot Appliance Dimension Diagram Reference Materials Vent Components Diagrams DVP Vent Components BEK DVP-BEK2 DVP-TVHW DVP-TRAP Horizontal Termination Cap DVP-HRC-SS Effective SL-2DVP Adapter Service Parts Service Parts Stocked IPI Valve Assembly CNXT4842 Series Log/Grate Assembly Valve Assembly Optional Components Model Description Contact Information