Hearth and Home Technologies QV32B-A, QV36B-A manual

Top Vent - Vertical Termination - (continued)

Four 90º Elbows

V1 Min.			H1 Max.		V2 Min.		H2 Max.		V3 Min.
1-1/2 ft.	457 mm		4 ft.	1.2 m	4 ft.	1.2 m	4 ft.	1.2 m	3-1/2 ft.	1.0 m

		V1 + V2 + V3 + H1 + H2 Maximum= 40 ft. (12.2 m)

Note: Use SLP Series components only.

Note: There MUST be a 25% reduction in total H when using ﬂex vent except when using the simple up and out installation (see Figure 5.3).

Figure 7.11

30	Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12

Page 30

Image 30

Hearth and Home Technologies QV32B-A Top Vent Vertical Termination Four 90º Elbows, V1 Min H1 Max V2 Min H2 Max V3 Min

Contents

Models What to do if you smell gasHOT Surfaces Congratulations Homeowner Reference Information Table of Contents User Guide Finishing Appliance SetupTroubleshooting Reference Materials Limited Lifetime Warranty Limited Lifetime Warranty Warranty Conditions Listing and Code Approvals Installation of Carbon Monoxide Detectors Requirements for the Commonwealth of Massachusetts Gas Fireplace Safety Operating Instructions User GuideYour Fireplace Fan Kit optional Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Clear Space Lighting Instructions Standing Pilot Final inspection byWhat to do if YOU Smell GAS Frequently Asked Questions Issue SolutionsAfter Fireplace is Lit Maintenance and Service Logs Maintenance Tasks-Qualiﬁed Service TechnicianGasket Seal and Glass Assembly Inspection Firebox Getting Started Typical Appliance System Design and Installation Considerations Tools and Supplies NeededInspect Appliance and Components Framing and Clearances Selecting Appliance Location Constructing the Appliance Chase ClearancesModels Mantel and Wall Projections Combustible MantelsCombustible Mantel Legs or Wall Projections Termination Locations Vent Termination Minimum ClearancesOpening Covered Alcove Applications Minimum Clearances for Termination Vent Table Key Vent Information and DiagramsApproved Pipe Use of Elbows Use of Flex Vent Clearance Top Vent Horizontal Termination Venting with 1 elbow Propane Minimum Maximum Venting with 2 elbows NG Venting with 2 elbows Propane V1 Minimum H1 + H2 Maximum Top Vent Horizontal Termination Venting with 3 elbows NG Minimum + H 2 Maximum Top Vent Vertical Termination No Elbow = 60 ft. Max .3 m Exhaust restrictor Instructions Minimum Maximum + V 2 Minimum Top Vent Vertical Termination Venting with 2 elbows NGTop Vent Vertical Termination Venting with 2 elbows Propane V1 Minimum H1 Maximum V1 + V2 Minimum Top Vent Vertical Termination Venting with 3 elbows NG Top Vent Vertical Termination Venting with 3 elbows Propane Top Vent Vertical Termination Four 90º Elbows V1 Min H1 Max V2 Min H2 Max V3 Min H1 MAX V1 MIN H2 MAX H1 + H2 MAX H1 + H2 MAX H1 + H2+ H3 MAX Rear Vent Horizontal Termination Venting with 3 elbowsRear Vent Vertical Termination Venting with 1 elbow MIN MAX Rear Vent Vertical Termination Venting with 2 elbows Rear Vent Vertical Termination Venting with 3 elbows+ H 2 MAX MIN Clearances to Combustibles Prior to installing the gas applianceCoaxial to Colinear Venting Termination Cap Flue Damper Rear Vent Connecting the DV-46DVA-GCL Adapter to Appliance Top VentConnecting the LINK-DV30B to the DV-46DVA-GCL adapter Minimum Wall Penetration Framing Vent Clearances and FramingPipe Clearances to Combustibles Combustible Wall Penetration Install the Ceiling Firestop Installing Ceiling Firestop Install Attic Insulation Shield Flat Ceiling InstallationVaulted Ceiling Installation Appliance Preparation Top Vent Rear Vent Cut the metal retaining band and fold the sides out Securing and Leveling the Appliance 11 Proper Positioning and Securing of an Appliance Assemble Vent Sections DVP Pipe Only Installing Vent Pipe DVP and SLP PipeAttach Vent to the Firebox Assembly Assemble Pipe Sections Assemble Vent Sections SLP Pipe Only Assemble Slip Sections Secure the Vent Sections Disassemble Vent Sections Install Decorative Ceiling Components SLP only Install Metal Roof Flashing Assemble and Install Storm CollarFoot minimum in snow regions Install Vertical Termination Cap Install Decorative Wall Components SLP onlyHeat Shield Requirements for Horizontal Termination Install Horizontal Termination Cap DVP and SLP Pipe 20 Venting through the wall Gas Pressure Gas InformationFuel Conversion Gas Connection Wiring Requirements Optional Accessories RequirementsElectrical Information Junction Box Installation Wall Switch Installation for Fan Optional Finishing Facing Material NON-COMBUSTIBLE Board Included Appliance Setup Log Set Assembly LOGS-2014 Model QV32B-A Install the Log Assembly LOG Install Hood Install the MeshInstall Trim and/or Surround Air Shutter Setting Troubleshooting Symptom Possible Causes Corrective ActionStanding Pilot Ignition System Troubleshooting Symptom Possible Cause Corrective Action Appliance Dimension Diagram Reference MaterialsInches Millimeters Vent Components Diagrams Quadra-Fire QV32B-A, QV36B-A 2014-900 Rev. U 1/12 DVP-TRAP DVP vent components DVP-TRAPFL RF6M RF12MBEK DVP-BEK2 COOL-ADD 251 mm 222 mm 165 mm 165 mm9-1/4 235 mm 152 mm 168 mmElbow Elbow Effective Height Length SLP-DCF-BK SLP-SNKD SLP-CCS-BKSL-2DVP SLP-WT-BK Vent Components Diagrams Coaxial to Colinear Venting LINK-DV30B DV-46DVA-GCL At Depot Service PartsLog Set Assembly Direct Vent Gas Fireplace See valve assembly QV36B-A 12.5 12.7 12.6 12.8 12.15 12.9 #12 Burner/Valve AssemblyPart number list on following 12.13 Service Parts QV32B-A, QV36B-A Stocked QV32B-A Conversion Kits QV36B-A Conversion Kits Contact Information

Hearth and Home Technologies QV32B-A, QV36B-A Top Vent Vertical Termination Four 90º Elbows

Models: QV32B-A QV36B-A

Top Vent - Vertical Termination - (continued)

Four 90º Elbows

V1 Min.

H1 Max.

V2 Min.

H2 Max.

V3 Min.