Facing Material | Hearth and Home Technologies QV36B-A, QV32B-A

B. Facing Material

•Metal front faces may be covered with non-combustible materials only.

•Facing and/or ﬁnishing materials must not interfere with air ﬂow through louvers, operation of louvers or doors, or access for service.

•Facing and/or ﬁnishing materials must never overhang into the glass opening.

•Observe all clearances when applying combustible materials.

•Seal joints between the ﬁnished wall and appliance top and sides using a 300ºF minimum sealant. Refer to Figure 13.5.

WARNING! Risk of Fire! DO NOT apply combustible materials beyond the minimum clearances. Comply with all minimum clearances to combustibles as speciﬁed in this manual. Overlapping materials could ignite and will interfere with proper operation of doors and louvers.

	FACING MATERIAL UP TO 1/2 IN. THICK
	MAY BE COMBUSTIBLE - TOP AND SIDES
	NON-COMBUSTIBLE	0 IN.
	BOARD (INCLUDED)	0 IN.
	BOARD (INCLUDED)
	1 IN.
	1 IN.	1 IN.
	0 IN.	0 IN.
	HIGH TEMPERATURE (300º F / 149º C MIN.)
	TOP & SIDE SEAL JOINT
	BOTTOM 1 INCH MAY BE COVERED WITH
	COMBUSTIBLE OR NON-COMBUSTIBLE
	MATERIAL.
	Figure 13.5 Noncombustible Facing Diagram

Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12

53

Image 53

Hearth and Home Technologies QV36B-A, QV32B-A owner manual Facing Material, NON-COMBUSTIBLE Board Included

Contents

HOT Surfaces ModelsWhat to do if you smell gas Homeowner Reference Information Congratulations User Guide Table of Contents Troubleshooting Appliance SetupFinishing Reference Materials Limited Lifetime Warranty Limited Lifetime Warranty Warranty Conditions Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Installation of Carbon Monoxide Detectors Your Fireplace Gas Fireplace SafetyOperating Instructions User Guide Remote Controls, Wall Controls and Wall Switches Fixed Glass AssemblyFan Kit optional Clear Space What to do if YOU Smell GAS Lighting Instructions Standing PilotFinal inspection by After Fireplace is Lit Frequently Asked QuestionsIssue Solutions Maintenance and Service Gasket Seal and Glass Assembly Inspection Maintenance Tasks-Qualiﬁed Service TechnicianLogs Firebox Typical Appliance System Getting Started Inspect Appliance and Components Design and Installation ConsiderationsTools and Supplies Needed Selecting Appliance Location Framing and Clearances Models Constructing the Appliance ChaseClearances Combustible Mantel Legs or Wall Projections Mantel and Wall ProjectionsCombustible Mantels Opening Termination LocationsVent Termination Minimum Clearances Minimum Clearances for Termination Covered Alcove Applications Approved Pipe Vent Information and DiagramsVent Table Key Use of Elbows Clearance Use of Flex Vent Minimum Maximum Top Vent Horizontal Termination Venting with 1 elbow Propane V1 Minimum H1 + H2 Maximum Venting with 2 elbows NG Venting with 2 elbows Propane Minimum + H 2 Maximum Top Vent Horizontal Termination Venting with 3 elbows NG Exhaust restrictor Instructions Top Vent Vertical Termination No Elbow = 60 ft. Max .3 m Top Vent Vertical Termination Venting with 2 elbows Propane Top Vent Vertical Termination Venting with 2 elbows NGMinimum Maximum + V 2 Minimum V1 Minimum H1 Maximum V1 + V2 Minimum Top Vent Vertical Termination Venting with 3 elbows Propane Top Vent Vertical Termination Venting with 3 elbows NG V1 Min H1 Max V2 Min H2 Max V3 Min Top Vent Vertical Termination Four 90º Elbows H1 + H2 MAX H1 MAX V1 MIN H2 MAX Rear Vent Vertical Termination Venting with 1 elbow Rear Vent Horizontal Termination Venting with 3 elbowsH1 + H2 MAX H1 + H2+ H3 MAX MIN MAX + H 2 MAX MIN Rear Vent Vertical Termination Venting with 2 elbowsRear Vent Vertical Termination Venting with 3 elbows Coaxial to Colinear Venting Prior to installing the gas applianceClearances to Combustibles Termination Cap Flue Damper Connecting the LINK-DV30B to the DV-46DVA-GCL adapter Connecting the DV-46DVA-GCL Adapter to Appliance Top VentRear Vent Minimum Pipe Clearances to Combustibles Vent Clearances and FramingWall Penetration Framing Combustible Wall Penetration Installing Ceiling Firestop Install the Ceiling Firestop Vaulted Ceiling Installation Install Attic Insulation ShieldFlat Ceiling Installation Top Vent Appliance Preparation Cut the metal retaining band and fold the sides out Rear Vent 11 Proper Positioning and Securing of an Appliance Securing and Leveling the Appliance Attach Vent to the Firebox Assembly Installing Vent Pipe DVP and SLP PipeAssemble Vent Sections DVP Pipe Only Assemble Pipe Sections Assemble Slip Sections Assemble Vent Sections SLP Pipe Only Disassemble Vent Sections Secure the Vent Sections Install Decorative Ceiling Components SLP only Foot minimum in snow regions Install Metal Roof FlashingAssemble and Install Storm Collar Heat Shield Requirements for Horizontal Termination Install Vertical Termination CapInstall Decorative Wall Components SLP only 20 Venting through the wall Install Horizontal Termination Cap DVP and SLP Pipe Fuel Conversion Gas InformationGas Pressure Gas Connection Electrical Information Wiring RequirementsOptional Accessories Requirements Wall Switch Installation for Fan Optional Junction Box Installation Finishing NON-COMBUSTIBLE Board Included Facing Material Appliance Setup Install the Log Assembly Log Set Assembly LOGS-2014 Model QV32B-A LOG Install Trim and/or Surround Install the MeshInstall Hood Air Shutter Setting Standing Pilot Ignition System TroubleshootingSymptom Possible Causes Corrective Action Symptom Possible Cause Corrective Action Troubleshooting Inches Millimeters Appliance Dimension DiagramReference Materials Quadra-Fire QV32B-A, QV36B-A 2014-900 Rev. U 1/12 Vent Components Diagrams DVP vent components DVP-TRAP BEK DVP-BEK2 RF6M RF12MDVP-TRAPFL COOL-ADD Elbow 222 mm 165 mm 165 mm9-1/4 235 mm 152 mm 168 mm251 mm Elbow Effective Height Length SL-2DVP SLP-SNKD SLP-CCS-BKSLP-DCF-BK SLP-WT-BK LINK-DV30B DV-46DVA-GCL Vent Components Diagrams Coaxial to Colinear Venting Log Set Assembly Service PartsAt Depot Direct Vent Gas Fireplace QV36B-A See valve assembly Part number list on following #12 Burner/Valve Assembly12.5 12.7 12.6 12.8 12.15 12.9 12.13 Stocked Service Parts QV32B-A, QV36B-A QV36B-A Conversion Kits QV32B-A Conversion Kits Contact Information