Manuals / Heat & Glo LifeStyle / Household Appliance / Indoor Fireplace

Heat & Glo LifeStyle 6000TRS-CD manual Step Positioning Leveling, and Securing the Fireplace

Models: 6000TRS-CD

1 42

Download 42 pages 3.32 Kb

Page 29

Image 29

Step 4

Positioning,

Leveling, and

Securing the

Fireplace

1.Place the fireplace into position.

2.Level the fireplace from side to side and from front to back.

3.Shim the fireplace with non-combus- tible material, such as sheet metal, as necessary.

4.Secure the fireplace to the framing by nailing or screwing.

Step 5

The Gas Control

System

The diagram below shows how to properly position, level, and secure the fireplace.

NAILING TABS (BOTH SIDES)

Figure 26. Proper Positioning, Leveling, and

Securing of a Fireplace

WARNING: THIS UNIT IS NOT FOR ! USE WITH SOLID FUEL.

Standing Pilot Ignition System

This system includes millivolt control valve, standing pilot, thermopile/thermocouple flame sensor, and piezo ignitor.

WARNING: 230 VAC MUST NEVER BE

!CONNECTED TO A CONTROL VALVE IN A MILLIVOLT SYSTEM.

STANDING PILOT

Figure 27. Gas Control System

Page 29

Image 29

Heat & Glo LifeStyle 6000TRS-CD manual Step Positioning Leveling, and Securing the Fireplace, Step The Gas Control System

Contents

6000TRS-CE 0087Model What to do if you smell gasTHIS UNIT IS NOT FOR USE WITH SOLID FUEL SAFETY AND WARNING INFORMATIONService Parts List Table of ContentsSection 3 Installing the Fireplace Section 5 Troubleshooting6000TRS-CE Service Parts9 Log Set Assembly NG, LP Exploded Parts DiagramACCESSORIES NG Service Parts List6000TRS-CE Service Parts Standing Pilot Valve Assembly6000TRS-CE DESCRIPTIONApprovals and Regulations Installation RegulationsAppliance Certification MODELGetting Started Pre-installation PreparationIntroducing the Heat & Glo Gas Fireplaces ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARDFigure 1. Diagram of the 6000TRS-CE Figure 2. Fireplace Dimensions, Locations, and Space Requirements Installing the FireplaceStep Locating the Fireplace Clearance RequirementsFigure 4. Framing Dimensions MEASURE FIREPLACE DIMENSIONS, ANDStep Framing theA. Flue System Approvals Step Installing the Flue SystemIdentifying Flue Components Figure 5. Flue Components and Terminations10.2cm 15.2cm 30.5cm DVP4 DVP6 NOTE PIPES OVERLAP 32 mm AT EACH JOINTDVP12 31.0cm MAX DVP12A 36.2cm 5.1cm MIN 61.0cmFigure 8. Straight Out Horizontal Flue Figure 7. Straight up Vertical FlueMIN. RUN MAX. RUNFigure 10. Flue with One 90 Elbow Flue with One 90 ElbowFLUE WITH TWO 2 90 ELBOWS Figure 11. Flue with Two 90 ElbowsH + H H1 V HFLUE WITH TWO 2 90 ELBOWS Figure 12. Flue with Two 90 ElbowsH + H V1 V HFLUE WITH THREE 3 90 ELBOWS Figure 13. Flue with three 90 elbowsH + H FLUE WITH THREE 3 90 ELBOWSFLUE WITH THREE 3 90 ELBOWS Figure 14. Flue with three 90 elbowsH + H FLUE WITH THREE 3 90 ELBOWSVenting Out the Rear Flue B. Installing Flue ComponentsWARNING THE TOP HEAT SHIELD INSIDE Venting Out the Top Flue2. Install Support Brackets Installing Flue ComponentsTo install support brackets for horizontal runs B. On the TOP of the heaterFigure 17. Installing Support Brackets 3. Install FirestopsTo install firestops for vertical runs that pass through ceilings For Horizontal Terminations using the DVP-TRAP SIDING, IT IS NECESSARY TO INSTALL THE VINYLC. Flue Termination IF EXTERIOR WALLS ARE FINISHED WITH VINYLMUST BE POSITIONED SO THAT THE ARROW IS POINTING UP WARNING THE TERMINATION CAPRear Vent Heat ShieldMake the outline of the roof hole around the centerpoint nail This also pertains to vertical flue systems installed TERMINALS, AND PLACEMENT OF GASFOLLOW NATIONAL REGULATIONS AND CODES OF PRACTICE FORAlcove Applications = AREA WHERE TERMINAL IS NOT PERMITTED= VENT TERMINAL X = AIR SUPPLY INLETStep The Gas Control System Step Positioning Leveling, and Securing the FireplaceSecuring of a Fireplace Standing Pilot Ignition SystemDO NOT USE AN OPEN FLAME TO CHECK FOR GAS LEAKS Step The Gas Supply LineOptional Accessories Step Wiring the FireplaceWall Switch RequirementsFigure 29. Standing Pilot Ignition Wiring Diagram WHEN SERVICING CONTROLS. WIRING ERStep Finishing OUS OPERATION. VERIFY PROPER OPERAInstalling the Trim Figure 32. Holding TabsStep 10 Installing Trim, Refractory, Logs, and Ember Material Installing the Ceramic RefractoryINSTRUCTIONS LOG PLACEMENTLog Set Assembly LOGS-6TRSCE grate as shown LOG #3 SRV385-723 Rest log #3 on the grooves on log #1 and log #2Placing the Ember Material Figure 33. GlassAssemblyFigure 34. Placement of the Ember Material Review safety warnings and cautions After the InstallationDouble-check for faulty components Step Before Lighting the Fireplace Step Lighting the FireplaceMaintaining and Servicing Your Fireplace Fireplace MaintenanceFireplace Maintenance Task To MaintenanceSTANDING PILOT Figure 35. Burner Flame PatternsFigure 36. Pilot Flame Patterns Trouble- shooting Standing Pilot TroubleshootingSymptom Possible CausePossible Cause SymptomCorrective Action 3. ContinuedCorrective Action SymptomPossible Cause