Manuals / Heat & Glo LifeStyle / Household Appliance / Indoor Fireplace

Heat & Glo LifeStyle 6000TRS-CD manual Standing Pilot Valve Assembly, 6000TRS-CE, Service Parts

Models: 6000TRS-CD

1 42

Page 6

Service Parts	6000TRS-CE

(NG) Exploded Parts Diagram	Beginning Manufacturing Date: 1-04
	Ending Manufacturing Date: ______

Standing Pilot Valve Assembly

	9	13
	9
	10	12
		11


ITEM	DESCRIPTION		SERIAL #	PART NUMBER

1	Pilot Assembly NG			529-540A

2	Pilot Bracket			2049-105

3	Orifice NG (#33)			582-833

4	30.5 cm Flex			383-302A

5	Burner Neck Gasket			438-407

6	Valve Plate Gasket			385-402

7	Valve Bracket			2049-108

8	Flex Assembly			302-330A

9	Wire Assembly			049-552A

10	ON/Off Rocker Switch			060-521A

11	Piezo Ignitor			219-513

12	Control Panel			2049-109

13	S.I.T. Valve NG			060-524

Page 6

Image 6

Heat & Glo LifeStyle 6000TRS-CD manual Standing Pilot Valve Assembly, 6000TRS-CE, Service Parts, Description, Serial #

Contents

Model 00876000TRS-CE What to do if you smell gasSAFETY AND WARNING INFORMATION THIS UNIT IS NOT FOR USE WITH SOLID FUELSection 3 Installing the Fireplace Table of ContentsService Parts List Section 5 Troubleshooting9 Log Set Assembly Service Parts6000TRS-CE NG, LP Exploded Parts DiagramNG Service Parts List 6000TRS-CEACCESSORIES 6000TRS-CE Standing Pilot Valve AssemblyService Parts DESCRIPTIONAppliance Certification Installation RegulationsApprovals and Regulations MODELIntroducing the Heat & Glo Gas Fireplaces Pre-installation PreparationGetting Started ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARDFigure 1. Diagram of the 6000TRS-CE Step Locating the Fireplace Installing the FireplaceFigure 2. Fireplace Dimensions, Locations, and Space Requirements Clearance RequirementsStep MEASURE FIREPLACE DIMENSIONS, ANDFigure 4. Framing Dimensions Framing theIdentifying Flue Components Step Installing the Flue SystemA. Flue System Approvals Figure 5. Flue Components and TerminationsDVP12 31.0cm MAX DVP12A NOTE PIPES OVERLAP 32 mm AT EACH JOINT10.2cm 15.2cm 30.5cm DVP4 DVP6 36.2cm 5.1cm MIN 61.0cmMIN. RUN Figure 7. Straight up Vertical FlueFigure 8. Straight Out Horizontal Flue MAX. RUNFlue with One 90 Elbow Figure 10. Flue with One 90 ElbowH + H Figure 11. Flue with Two 90 ElbowsFLUE WITH TWO 2 90 ELBOWS H1 V HH + H Figure 12. Flue with Two 90 ElbowsFLUE WITH TWO 2 90 ELBOWS V1 V HH + H Figure 13. Flue with three 90 elbowsFLUE WITH THREE 3 90 ELBOWS FLUE WITH THREE 3 90 ELBOWSH + H Figure 14. Flue with three 90 elbowsFLUE WITH THREE 3 90 ELBOWS FLUE WITH THREE 3 90 ELBOWSWARNING THE TOP HEAT SHIELD INSIDE B. Installing Flue ComponentsVenting Out the Rear Flue Venting Out the Top FlueTo install support brackets for horizontal runs Installing Flue Components2. Install Support Brackets B. On the TOP of the heater3. Install Firestops Figure 17. Installing Support BracketsTo install firestops for vertical runs that pass through ceilings C. Flue Termination SIDING, IT IS NECESSARY TO INSTALL THE VINYLFor Horizontal Terminations using the DVP-TRAP IF EXTERIOR WALLS ARE FINISHED WITH VINYLRear Vent WARNING THE TERMINATION CAPMUST BE POSITIONED SO THAT THE ARROW IS POINTING UP Heat ShieldMake the outline of the roof hole around the centerpoint nail FOLLOW NATIONAL REGULATIONS TERMINALS, AND PLACEMENT OF GASThis also pertains to vertical flue systems installed AND CODES OF PRACTICE FOR= VENT TERMINAL = AREA WHERE TERMINAL IS NOT PERMITTEDAlcove Applications X = AIR SUPPLY INLETSecuring of a Fireplace Step Positioning Leveling, and Securing the FireplaceStep The Gas Control System Standing Pilot Ignition SystemStep The Gas Supply Line DO NOT USE AN OPEN FLAME TO CHECK FOR GAS LEAKSWall Switch Step Wiring the FireplaceOptional Accessories RequirementsStep Finishing WHEN SERVICING CONTROLS. WIRING ERFigure 29. Standing Pilot Ignition Wiring Diagram OUS OPERATION. VERIFY PROPER OPERAStep 10 Installing Trim, Refractory, Logs, and Ember Material Figure 32. Holding TabsInstalling the Trim Installing the Ceramic RefractoryLOG PLACEMENT Log Set Assembly LOGS-6TRSCEINSTRUCTIONS LOG #3 SRV385-723 Rest log #3 on the grooves on log #1 and log #2 grate as shownFigure 33. GlassAssembly Figure 34. Placement of the Ember MaterialPlacing the Ember Material Double-check for faulty components After the InstallationReview safety warnings and cautions Step Before Lighting the Fireplace Step Lighting the FireplaceFireplace Maintenance Task To Fireplace MaintenanceMaintaining and Servicing Your Fireplace MaintenanceFigure 35. Burner Flame Patterns Figure 36. Pilot Flame PatternsSTANDING PILOT Symptom Standing Pilot TroubleshootingTrouble- shooting Possible CauseCorrective Action SymptomPossible Cause 3. ContinuedSymptom Possible CauseCorrective Action

Standing Pilot Valve Assembly

DESCRIPTION

SERIAL #

PART NUMBER