Manuals / Heat & Glo LifeStyle / Household Appliance / Indoor Fireplace

Heat & Glo LifeStyle 6000TRS-CD manual Table of Contents, Service Parts List, Getting Started

Models: 6000TRS-CD

1 42

Download 42 pages 3.32 Kb

Page 3

Safety and Warning Information		2
Service Parts List		4
Section 1: Approvals and Regulations		7
Appliance Certification		7
Installation Regulations		7
Section 2: Getting Started		8
Introducing the Heat & Glo Gas Fireplaces		8
Pre-installation Preparation		8
Section 3: Installing the Fireplace		10
Step 1	Locating the Fireplace	10
Step 2	Framing the Fireplace	11
Step 3	Installing the Flue System	12
	A. Flue System Approvals	12
	B. Installing Flue Components	20
	C. Flue Termination	24
Step 4	Positioning, Leveling and
	Securing the Fireplace	29
Step 5	The Gas Control Systems	29
Step 6	The Gas Supply Line	30
Step 7	Gas Pressure Requirements	31
Step 8	Wiring the Fireplace	31
Step 9	Finishing	32
Step 10	Installing Trim, Logs & Ember Material	33
	Installing the Trim	33
	Positioning the Logs	34
	Placing the Ember Material	36
Step 11	Before Lighting the Fireplace	37
Step 12	Lighting the Fireplace	37
	After the Installation	37
Section 4: Maintaining and Servicing
	Your Fireplace	38
Section 5: Troubleshooting		40
	= Contains updated information.

Table of Contents

3

Image 3

Heat & Glo LifeStyle 6000TRS-CD manual Table of Contents, Service Parts List, Getting Started, Installing the Fireplace

Contents

What to do if you smell gas 00876000TRS-CE ModelTHIS UNIT IS NOT FOR USE WITH SOLID FUEL SAFETY AND WARNING INFORMATIONSection 5 Troubleshooting Table of ContentsService Parts List Section 3 Installing the FireplaceNG, LP Exploded Parts Diagram Service Parts6000TRS-CE 9 Log Set AssemblyNG Service Parts List 6000TRS-CEACCESSORIES DESCRIPTION Standing Pilot Valve AssemblyService Parts 6000TRS-CEMODEL Installation RegulationsApprovals and Regulations Appliance CertificationANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARD Pre-installation PreparationGetting Started Introducing the Heat & Glo Gas FireplacesFigure 1. Diagram of the 6000TRS-CE Clearance Requirements Installing the FireplaceFigure 2. Fireplace Dimensions, Locations, and Space Requirements Step Locating the FireplaceFraming the MEASURE FIREPLACE DIMENSIONS, ANDFigure 4. Framing Dimensions StepFigure 5. Flue Components and Terminations Step Installing the Flue SystemA. Flue System Approvals Identifying Flue Components36.2cm 5.1cm MIN 61.0cm NOTE PIPES OVERLAP 32 mm AT EACH JOINT10.2cm 15.2cm 30.5cm DVP4 DVP6 DVP12 31.0cm MAX DVP12AMAX. RUN Figure 7. Straight up Vertical FlueFigure 8. Straight Out Horizontal Flue MIN. RUNFigure 10. Flue with One 90 Elbow Flue with One 90 ElbowH1 V H Figure 11. Flue with Two 90 ElbowsFLUE WITH TWO 2 90 ELBOWS H + HV1 V H Figure 12. Flue with Two 90 ElbowsFLUE WITH TWO 2 90 ELBOWS H + HFLUE WITH THREE 3 90 ELBOWS Figure 13. Flue with three 90 elbowsFLUE WITH THREE 3 90 ELBOWS H + HFLUE WITH THREE 3 90 ELBOWS Figure 14. Flue with three 90 elbowsFLUE WITH THREE 3 90 ELBOWS H + HVenting Out the Top Flue B. Installing Flue ComponentsVenting Out the Rear Flue WARNING THE TOP HEAT SHIELD INSIDEB. On the TOP of the heater Installing Flue Components2. Install Support Brackets To install support brackets for horizontal runsFigure 17. Installing Support Brackets 3. Install FirestopsTo install firestops for vertical runs that pass through ceilings IF EXTERIOR WALLS ARE FINISHED WITH VINYL SIDING, IT IS NECESSARY TO INSTALL THE VINYLFor Horizontal Terminations using the DVP-TRAP C. Flue TerminationHeat Shield WARNING THE TERMINATION CAPMUST BE POSITIONED SO THAT THE ARROW IS POINTING UP Rear VentMake the outline of the roof hole around the centerpoint nail AND CODES OF PRACTICE FOR TERMINALS, AND PLACEMENT OF GASThis also pertains to vertical flue systems installed FOLLOW NATIONAL REGULATIONSX = AIR SUPPLY INLET = AREA WHERE TERMINAL IS NOT PERMITTEDAlcove Applications = VENT TERMINALStanding Pilot Ignition System Step Positioning Leveling, and Securing the FireplaceStep The Gas Control System Securing of a FireplaceDO NOT USE AN OPEN FLAME TO CHECK FOR GAS LEAKS Step The Gas Supply LineRequirements Step Wiring the FireplaceOptional Accessories Wall SwitchOUS OPERATION. VERIFY PROPER OPERA WHEN SERVICING CONTROLS. WIRING ERFigure 29. Standing Pilot Ignition Wiring Diagram Step FinishingInstalling the Ceramic Refractory Figure 32. Holding TabsInstalling the Trim Step 10 Installing Trim, Refractory, Logs, and Ember MaterialLOG PLACEMENT Log Set Assembly LOGS-6TRSCEINSTRUCTIONS grate as shown LOG #3 SRV385-723 Rest log #3 on the grooves on log #1 and log #2Figure 33. GlassAssembly Figure 34. Placement of the Ember MaterialPlacing the Ember Material Step Before Lighting the Fireplace Step Lighting the Fireplace After the InstallationReview safety warnings and cautions Double-check for faulty componentsMaintenance Fireplace MaintenanceMaintaining and Servicing Your Fireplace Fireplace Maintenance Task ToFigure 35. Burner Flame Patterns Figure 36. Pilot Flame PatternsSTANDING PILOT Possible Cause Standing Pilot TroubleshootingTrouble- shooting Symptom3. Continued SymptomPossible Cause Corrective ActionSymptom Possible CauseCorrective Action