Manuals / Heat & Glo LifeStyle / Household Appliance / Indoor Fireplace

Heat & Glo LifeStyle 6000TRS-CD manual Step Finishing, When Servicing Controls. Wiring Er

Models: 6000TRS-CD

1 42

Download 42 pages 3.32 Kb

Page 32

LABEL ALL WIRES PRIOR TO DISCONNECTION

!WARNING: DO NOT CONNECT 230 VAC TO THE WALL SWITCH OR THE CONTROL VALVE WILL BE DESTROYED.

CAUTION	LABEL ALL WIRES PRIOR TO DISCONNECTION
	WHEN SERVICING CONTROLS. WIRING ER-
	RORS CAN CAUSE IMPROPER AND DANGER-
	OUS OPERATION. VERIFY PROPER OPERA-
	TION AFTER SERVICING.

	OPTIONAL WALL SWITCH
	THERMOSTAT OR REMOTE
			THERMOCOUPLE
			TP/TH
		OFF	TP
		OFF	TH
			TH
		ON	THERMOPILE
		ON/OFF	THERMOPILE
	REMOTE SWITCH	ON/OFF	GAS VALVE
	REMOTE SWITCH	SWITCH	GAS VALVE
	PIGTAIL	SWITCH
	PIGTAIL

Figure 29. Standing Pilot Ignition Wiring Diagram

Step 9

Finishing

Only non-combustible materials may be used to cover the black fireplace front.

The following diagram shows the minimum vertical and corresponding maximum horizontal dimensions of fireplace mantels or other combustible projections above the top front edge of the fireplace. See Figures 2 , 3 and 4 for other fireplace clearances.

45o
30.5
27.9
25.4
22.7
20.3
15.8
12.715.2
7.6 10.2
5
TOP FRONT EDGE
OF FIREPLACE
NOTE: ALL DIMENSIONS SHOWN
IN CENTIMETERS

32

Figure 30. Minimum Vertical and Maximum Horizontal Dimensions of Combustibles

above Fireplace

!WARNING: WHEN FINISHING THE FIREPLACE, NEVER OBSTRUCT OR MODIFY THE AIR INLET/OUTLET GRILLES IN ANY MANNER.

Image 32

Heat & Glo LifeStyle 6000TRS-CD Step Finishing, When Servicing Controls. Wiring Er, Ous Operation. Verify Proper Opera

Contents

0087 6000TRS-CEModel What to do if you smell gasSAFETY AND WARNING INFORMATION THIS UNIT IS NOT FOR USE WITH SOLID FUELTable of Contents Service Parts ListSection 3 Installing the Fireplace Section 5 TroubleshootingService Parts 6000TRS-CE9 Log Set Assembly NG, LP Exploded Parts DiagramACCESSORIES NG Service Parts List6000TRS-CE Standing Pilot Valve Assembly Service Parts6000TRS-CE DESCRIPTIONInstallation Regulations Approvals and RegulationsAppliance Certification MODELPre-installation Preparation Getting StartedIntroducing the Heat & Glo Gas Fireplaces ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARDFigure 1. Diagram of the 6000TRS-CE Installing the Fireplace Figure 2. Fireplace Dimensions, Locations, and Space RequirementsStep Locating the Fireplace Clearance RequirementsMEASURE FIREPLACE DIMENSIONS, AND Figure 4. Framing DimensionsStep Framing theStep Installing the Flue System A. Flue System ApprovalsIdentifying Flue Components Figure 5. Flue Components and TerminationsNOTE PIPES OVERLAP 32 mm AT EACH JOINT 10.2cm 15.2cm 30.5cm DVP4 DVP6DVP12 31.0cm MAX DVP12A 36.2cm 5.1cm MIN 61.0cmFigure 7. Straight up Vertical Flue Figure 8. Straight Out Horizontal FlueMIN. RUN MAX. RUNFlue with One 90 Elbow Figure 10. Flue with One 90 ElbowFigure 11. Flue with Two 90 Elbows FLUE WITH TWO 2 90 ELBOWSH + H H1 V HFigure 12. Flue with Two 90 Elbows FLUE WITH TWO 2 90 ELBOWSH + H V1 V HFigure 13. Flue with three 90 elbows FLUE WITH THREE 3 90 ELBOWSH + H FLUE WITH THREE 3 90 ELBOWSFigure 14. Flue with three 90 elbows FLUE WITH THREE 3 90 ELBOWSH + H FLUE WITH THREE 3 90 ELBOWSB. Installing Flue Components Venting Out the Rear FlueWARNING THE TOP HEAT SHIELD INSIDE Venting Out the Top FlueInstalling Flue Components 2. Install Support BracketsTo install support brackets for horizontal runs B. On the TOP of the heater3. Install Firestops Figure 17. Installing Support BracketsTo install firestops for vertical runs that pass through ceilings SIDING, IT IS NECESSARY TO INSTALL THE VINYL For Horizontal Terminations using the DVP-TRAPC. Flue Termination IF EXTERIOR WALLS ARE FINISHED WITH VINYLWARNING THE TERMINATION CAP MUST BE POSITIONED SO THAT THE ARROW IS POINTING UPRear Vent Heat ShieldMake the outline of the roof hole around the centerpoint nail TERMINALS, AND PLACEMENT OF GAS This also pertains to vertical flue systems installedFOLLOW NATIONAL REGULATIONS AND CODES OF PRACTICE FOR= AREA WHERE TERMINAL IS NOT PERMITTED Alcove Applications= VENT TERMINAL X = AIR SUPPLY INLETStep Positioning Leveling, and Securing the Fireplace Step The Gas Control SystemSecuring of a Fireplace Standing Pilot Ignition SystemStep The Gas Supply Line DO NOT USE AN OPEN FLAME TO CHECK FOR GAS LEAKSStep Wiring the Fireplace Optional AccessoriesWall Switch RequirementsWHEN SERVICING CONTROLS. WIRING ER Figure 29. Standing Pilot Ignition Wiring DiagramStep Finishing OUS OPERATION. VERIFY PROPER OPERAFigure 32. Holding Tabs Installing the TrimStep 10 Installing Trim, Refractory, Logs, and Ember Material Installing the Ceramic RefractoryINSTRUCTIONS LOG PLACEMENTLog Set Assembly LOGS-6TRSCE LOG #3 SRV385-723 Rest log #3 on the grooves on log #1 and log #2 grate as shownPlacing the Ember Material Figure 33. GlassAssemblyFigure 34. Placement of the Ember Material After the Installation Review safety warnings and cautionsDouble-check for faulty components Step Before Lighting the Fireplace Step Lighting the FireplaceFireplace Maintenance Maintaining and Servicing Your FireplaceFireplace Maintenance Task To MaintenanceSTANDING PILOT Figure 35. Burner Flame PatternsFigure 36. Pilot Flame Patterns Standing Pilot Troubleshooting Trouble- shootingSymptom Possible CauseSymptom Possible CauseCorrective Action 3. ContinuedCorrective Action SymptomPossible Cause