Manuals / Heat & Glo LifeStyle / Household Appliance / Indoor Fireplace

Heat & Glo LifeStyle 6000TRS-CD manual NG Service Parts List, 6000TRS-CE, Accessories

Models: 6000TRS-CD

1 42

Download 42 pages 3.32 Kb

Page 5

(NG) Service Parts List

6000TRS-CE

IMPORTANT: THIS IS DATED INFORMATION. The most current information is located on your dealers VIP site. When ordering, supply serial and model numbers to ensure correct service parts.

ITEM	PARTS	SERIAL #	PART NUMBER

1	Junction Box		546-250A

2	Burner NG		2049-010

3	Glass Door Assembly		GLA-6TRXI

4	Log Grate		2049-020

5	Base Refractory		2049-102

6	Hood		SRV60-143-BK

7	Door Assembly		392-180A

8	Top Louver Assembly		392-182A

9	Log Set Assembly		LOGS-6TRSCE

10	Log 1		SRV2049-700

11	Log 2		SRV2049-701

12	Log 3		SRV385-723

13	Log 4		SRV385-721

14	Log 5		SRV385-722

15	Surround		2026-108

	Refractory Kit		BRICK-6000-FB

16	Back Wall Refractory		SRV2027-730

17	Left Wall Refractory		SRV2027-731

18	Right Wall Refractory		SRV2027-732

19	Insulation Board		385-401

20	Exhaust Baffle		2049-101

	Flue Gasket		2025-114

	Pilot Orifice NG		529-512

	Insulation Mineral Wool		050-721

	ACCESSORIES
	Extended Vertical Baffle Kit		BAF-VERT

	Wall Switch Kit, Off-white		WSK-21

	Wall Switch Kit, White		WSK-21-W

	Conversion Kit NG		NGK-6TRS-CE

	Conversion Kit LP		LPK-6TRS-CE

	Conversion Kit Butane		BGK-6TRS-CE

Also see following page for Standing Pilot valve assembly service part numbers.

5

Image 5

Heat & Glo LifeStyle 6000TRS-CD manual NG Service Parts List, 6000TRS-CE, Accessories

Contents

6000TRS-CE 0087Model What to do if you smell gasTHIS UNIT IS NOT FOR USE WITH SOLID FUEL SAFETY AND WARNING INFORMATIONService Parts List Table of ContentsSection 3 Installing the Fireplace Section 5 Troubleshooting6000TRS-CE Service Parts9 Log Set Assembly NG, LP Exploded Parts DiagramACCESSORIES NG Service Parts List6000TRS-CE Service Parts Standing Pilot Valve Assembly6000TRS-CE DESCRIPTIONApprovals and Regulations Installation RegulationsAppliance Certification MODELGetting Started Pre-installation PreparationIntroducing the Heat & Glo Gas Fireplaces ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARDFigure 1. Diagram of the 6000TRS-CE Figure 2. Fireplace Dimensions, Locations, and Space Requirements Installing the FireplaceStep Locating the Fireplace Clearance RequirementsFigure 4. Framing Dimensions MEASURE FIREPLACE DIMENSIONS, ANDStep Framing theA. Flue System Approvals Step Installing the Flue SystemIdentifying Flue Components Figure 5. Flue Components and Terminations10.2cm 15.2cm 30.5cm DVP4 DVP6 NOTE PIPES OVERLAP 32 mm AT EACH JOINTDVP12 31.0cm MAX DVP12A 36.2cm 5.1cm MIN 61.0cmFigure 8. Straight Out Horizontal Flue Figure 7. Straight up Vertical FlueMIN. RUN MAX. RUNFigure 10. Flue with One 90 Elbow Flue with One 90 ElbowFLUE WITH TWO 2 90 ELBOWS Figure 11. Flue with Two 90 ElbowsH + H H1 V HFLUE WITH TWO 2 90 ELBOWS Figure 12. Flue with Two 90 ElbowsH + H V1 V HFLUE WITH THREE 3 90 ELBOWS Figure 13. Flue with three 90 elbowsH + H FLUE WITH THREE 3 90 ELBOWSFLUE WITH THREE 3 90 ELBOWS Figure 14. Flue with three 90 elbowsH + H FLUE WITH THREE 3 90 ELBOWSVenting Out the Rear Flue B. Installing Flue ComponentsWARNING THE TOP HEAT SHIELD INSIDE Venting Out the Top Flue2. Install Support Brackets Installing Flue ComponentsTo install support brackets for horizontal runs B. On the TOP of the heaterFigure 17. Installing Support Brackets 3. Install FirestopsTo install firestops for vertical runs that pass through ceilings For Horizontal Terminations using the DVP-TRAP SIDING, IT IS NECESSARY TO INSTALL THE VINYLC. Flue Termination IF EXTERIOR WALLS ARE FINISHED WITH VINYLMUST BE POSITIONED SO THAT THE ARROW IS POINTING UP WARNING THE TERMINATION CAPRear Vent Heat ShieldMake the outline of the roof hole around the centerpoint nail This also pertains to vertical flue systems installed TERMINALS, AND PLACEMENT OF GASFOLLOW NATIONAL REGULATIONS AND CODES OF PRACTICE FORAlcove Applications = AREA WHERE TERMINAL IS NOT PERMITTED= VENT TERMINAL X = AIR SUPPLY INLETStep The Gas Control System Step Positioning Leveling, and Securing the FireplaceSecuring of a Fireplace Standing Pilot Ignition SystemDO NOT USE AN OPEN FLAME TO CHECK FOR GAS LEAKS Step The Gas Supply LineOptional Accessories Step Wiring the FireplaceWall Switch RequirementsFigure 29. Standing Pilot Ignition Wiring Diagram WHEN SERVICING CONTROLS. WIRING ERStep Finishing OUS OPERATION. VERIFY PROPER OPERAInstalling the Trim Figure 32. Holding TabsStep 10 Installing Trim, Refractory, Logs, and Ember Material Installing the Ceramic RefractoryINSTRUCTIONS LOG PLACEMENTLog Set Assembly LOGS-6TRSCE grate as shown LOG #3 SRV385-723 Rest log #3 on the grooves on log #1 and log #2Placing the Ember Material Figure 33. GlassAssemblyFigure 34. Placement of the Ember Material Review safety warnings and cautions After the InstallationDouble-check for faulty components Step Before Lighting the Fireplace Step Lighting the FireplaceMaintaining and Servicing Your Fireplace Fireplace MaintenanceFireplace Maintenance Task To MaintenanceSTANDING PILOT Figure 35. Burner Flame PatternsFigure 36. Pilot Flame Patterns Trouble- shooting Standing Pilot TroubleshootingSymptom Possible CausePossible Cause SymptomCorrective Action 3. ContinuedCorrective Action SymptomPossible Cause