Mineral Wool, Accessories | Heat & Glo LifeStyle TIARAP-CTO specs

Figure 8.10 Place the twig with the center resting on the ﬂat area in the center of the burner and both ends positioned as shown.

G. Mineral Wool

WARNING

Explosion Risk.

•Follow ember placement instructions in manual.

•Do NOT place embers directly over burner ports.

•Replace ember material annually.

Improperly placed embers interferes with proper burner operation.

Figure 8.11 Apply dime size pieces sparingly along front edge of burner. Do not completely block ports.

H. Accessories

Install approved accessories per instructions included with accessories. Refer to Section 12 for appropriate accesso- ries.

WARNING

Shock or ﬁre risk.

Use ONLY optional accessories approved for this appliance.

•Using non-listed accessories voids warranty.

• Using non-listed accessories may result in a safety hazard.

•Only Hearth & Home Technologies approved accessories may be used safely.

August 1, 2008

Heat & Glo · Tiara Petite B · 7026-101K

Page 33

Image 33

Heat & Glo LifeStyle TIARAP-CTO, TIARAP-CES, TIARAP-BK, TIARAP-BR owner manual Mineral Wool, Accessories

Contents

Installation and Operation What to do if you smell gasHot glass will cause burns Location Hang tag attached to rear of appliance Congratulations Table of Contents 1Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Getting Started Design & Installation ConsiderationsTools and Supplies Needed Inspect Appliance & Components Appliance Location and Clearances Selecting Appliance LocationClearances to Combustibles Vent Termination Minimum Clearances 4Termination Locations Alcove Applications Venting Components Vent InformationUse of Elbows Measuring Standards Venting Guidelines How to Use the Vent Graph Step Horizontal Termination 203mm Vinyl Siding Direct Vent Pipe Vertical Termination Ceiling Joists Framing 2 in mm Long Wood Screws Twist-lock the vent cap and seal Level Cathedral Ceiling Support Box Cathedral Ceiling Class a Metal Chimney Type a & B Co-Axial to Co-Linear Type C Up & Out InstallationExisting Masonry Chimney Type D Hearth Mount Cut and bend flashing as needed to fit Sealant adhesive Flex Liner Flex Coupler Sheet Metal Screws Slim Line Wall Thimble Installing Slim Line Trim Ring and Heat ShieldAssembling Slim Line Trim Ring and Heat Shield Next FIG. C Minimum Clearance Gas Information Wire clipFuel Conversions Converting to LP Gas Screws Rubber Gasket Identification Label F Valve Regulator Replacement Gas Connection Gas Pressures High Altitude Installations Connecting to the Appliance Recommendation for WireStanding Pilot Ignition System Wiring Wire Size Max. Length To access the module Ignition Module Access and Battery Replacement Appliance Setup Remove Shipping Materials Flue Restrictor InstallationLeg Leveling System Intake Damper Operation Positioning the Logs Intake Air Shutter Adjustment Mineral Wool Accessories KIT Contents Blower Installation August 1 Heat & Glo · Tiara Petite B · 7026-101K 19 Complete Assembly Glass Replacement Warming Shelves Installation Operating Instructions Before Lighting ApplianceControls Lighting Appliance For Your Safety Read Before Lighting Frequently Asked Questions Initial Break-in ProcedureAfter Appliance is Lit Symptom Possible Cause Corrective Action Troubleshooting Be Placed in this Opening After servicing Maintaining and Servicing Appliance Necessary. USE Caution When CLEANING/HANDLING Ceramic Burner Maintenance Tasks Inspect Reference Materials Appliance Dimension Diagram SL-D Series Vent Components Vent Components Diagram HHT SL-P Vent Components List Termination Caps & Kits Description Tiara Petite B Service Parts List cont’d. Tiara Petite B Tiara Petite B Cast Parts Individual Pieces Accessories Date of Service Performed By Description of Service Service and Maintenance Log Limited Lifetime Warranty Heat & GLO GAS Appliance Products Warranty Policy Tiara Petite B Contact InformationDealer Telephone