Item |
| Phenomenon | Cause | Factory | Inspection, repair or adjustment | |||||
| standard | |||||||||
|
|
|
|
|
|
|
|
|
| |
1 |
|
|
|
|
|
|
|
| • Adjust the clearance between | |
|
|
| Hinge (A) ass’y |
|
|
| ||||
|
|
|
|
|
|
|
|
|
| the Bushing [115] and slide |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| |
|
| Slide pipe (A) |
|
|
|
| pipe (A) with the Seal Lock | |||
|
|
|
|
|
|
|
|
|
| Hex. Socket Set Screw M6 x |
|
|
|
|
|
|
|
|
|
| 10 [118]. Ensure that slide pipe |
|
|
|
|
|
|
|
|
|
| section slides smoothly with a |
|
|
|
|
|
|
|
|
|
| slide load of within 3 kgf. |
|
|
|
|
|
|
|
| |||
|
|
| Slide pipe (B) |
|
|
| ||||
|
|
|
|
|
|
|
| (g) Inaccurate | 0.1/65 | • Replace Fence (A) [55] or |
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| squareness between | (height of Fence (A) | Fence (B) [47] as necessary. |
|
|
| Fig. 62 | fences (A) and (B), | [55]) |
| ||||
|
|
| turn table and base | 0.1/49 |
| |||||
|
|
|
|
|
|
|
| causes the workpiece | (height of Fence (B) |
|
|
|
|
|
|
|
|
| to tilt at an angle and | [47]) |
|
|
|
|
|
|
|
|
| prevent accurate | (Fig. 63) |
|
|
|
|
|
|
|
|
| cutting. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| (h) Loose fitting of | - | • Check the fitting surfaces of |
|
|
|
|
|
|
|
| swiveling portion of |
| Hinge (A) Ass’y [87], Gear |
|
|
|
|
|
|
|
| hinge (A) ass’y and |
| Case [198] and Hinge Shaft |
|
|
|
|
|
|
|
| gear case, or sluggish |
| (A) [92] for any foreign |
|
|
|
|
|
|
|
| movement. As a result, |
| substance (such as cutting |
|
|
| Fig. 63 | components may be |
| dust) and remove it as | ||||
|
|
| deformed because of |
| necessary. | |||||
|
|
|
|
|
|
|
| unstable gear case or |
|
|
|
|
|
|
|
|
|
| because the operator |
|
|
|
|
|
|
|
|
|
| must apply excessive |
|
|
|
|
|
|
|
|
|
| pressure during |
|
|
|
|
|
|
|
|
|
| operation. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| (i) Excessively fast cutting | - | • Reduce the cutting speed |
|
|
|
|
|
|
|
| speed causes |
| (appropriately 6 seconds for a |
|
|
|
|
|
|
|
| deflection of saw blade |
| square wood workpiece of 60 |
|
|
|
|
|
|
|
| and inaccurate cutting. |
| mm |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| (j) Excessive cutting force | - | • Sharpen the saw blade again. |
|
|
|
|
|
|
|
| (pressure) is required |
|
|
|
|
|
|
|
|
|
| because of dull saw |
|
|
|
|
|
|
|
|
|
| blade. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| (k) The workpiece moves | - | • Correct bend, flex or other |
|
|
|
|
|
|
|
| during cutting because |
| deformation by planing and try |
|
|
|
|
|
|
|
| it is bent or deformed. |
| cutting. |
|
|
|
|
|
|
|
|
|
|
|
