Part names

Ports (See below.)

CB/PB

 

 

 

SD

CARD

 

 

 

 

CR/PR

 

 

 

 

 

 

 

 

 

 

RGB

 

 

 

 

 

VIDEO

A

A

IN1

AUX

 

 

 

 

UDIO

 

DC I/O

 

 

S-

 

UDIO IN2

IN1

 

5V

0.5A

 

 

VIDEO

 

 

 

 

 

RGB IN2

 

LAN

 

 

 

 

 

 

 

CONTROL

RGB

OUT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

UDIO

 

 

 

 

 

 

 

 

 

A

OUT

 

 

 

 

 

 

 

USB

 

 

Rear-Left side

IN AC

Power switch (19)

AC inlet (15)

Elevator button (10)

Elevator foot (10)

Vent

 

 

 

 

AUDIO IN1 port (

13)

 

 

 

 

 

 

 

(In the default setting, the AUDIO IN1 port is the audio

AUDIO IN3 L/R port (

14)

 

port for the RGB IN1 port, however, it is possible to

 

 

change the settings. 38)

 

 

 

(In the default setting, the

 

 

 

 

 

SD CARD slot (

13)

AUDIO IN3 L/R port is the audio

 

 

 

 

 

RGB IN1 port (

13)

This slot is used when

port for the VIDEO, S-VIDEO

 

and COMPONENT VIDEO

 

Restart switch (*) (

66)

utilizing SD CARD.

ports, however it is possible to

AUX I /O port (

13)

 

RGB IN2 port (

13)

change the settings.

38)

 

 

This port is used when

 

 

 

 

SD CARD

 

LAN

 

utilizing USB Memory.

COMPONENT

 

 

 

 

 

 

 

14)

 

 

 

AUX I/O

 

 

LAN port ( 13)

 

VIDEO ports (

Y

AUDIO IN3

 

 

 

 

 

R

 

 

 

 

Used for Ethernet

 

Y

 

 

 

 

 

 

 

 

 

 

 

RGB IN1

RGB IN2 RGB OUT

AUDIO OUT

 

input/output.

 

CB/PB

 

CB/PB

L

AUDIO IN1

 

 

 

 

 

 

 

 

This port is used

 

CR/PR

 

 

 

 

 

 

 

 

 

AUDIO IN2

 

 

 

 

 

CR/PR

 

K

USB

 

 

when utilizing network

 

 

 

 

CONTROL

 

 

 

 

VIDEO port (

14)

VIDEO

 

 

 

 

 

functions.

 

S-VIDEO

 

 

 

 

 

 

 

 

 

 

 

S-VIDEO port (

14)

 

 

 

 

Ports

 

AUDIO OUT port

 

 

 

 

 

 

 

 

13)

 

 

 

 

 

( 13)

13)

AUDIO IN2 port (

 

 

USB port (

13)

RGB OUT port (

(In the default setting, the AUDIO

 

 

 

 

 

IN2 port is the audio port for

 

CONTROL port (

13)

 

 

the RGB IN2 port, however, it is

 

 

possible to change the settings.

Kensington lock slot

38)

 

NOTE (*) About Restart switch: This projector is controlled by an internal microprocessor. Under certain exceptional circumstances, the projector may not operate correctly and the microprocessor will need to be reset. In such a case, please push the Restart switch by using a cocktail stick or similar, and before turning on again, make the projector cool down at least 10 minutes without operating. Only push the Restart switch in these exceptional instances.

6

Page 15
Image 15
Hitachi CP-X268AWF user manual Component, Cb/Pb, Cr/Pr