Table of Contents | Hobart Welding Products 210 MVP specs

TABLE OF CONTENTS

SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING		1
1-1.	Symbol Usage	1
1-2.	Arc Welding Hazards	1
1-3. Additional Symbols For Installation, Operation, And Maintenance		3
1-4. California Proposition 65 Warnings		4
1-5.	Principal Safety Standards	4
1-6.	EMF Information	4

SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT UTILISATION		5
2-1.	Symboles utilisés	5
2-2. Dangers relatifs au soudage à l’arc		5
2-3.	Dangers supplémentaires en relation avec l’installation, le fonctionnement et la maintenance	7
2-4. Proposition californienne 65 Avertissements		8
2-5.	Principales normes de sécurité	9
2-6.	Informations relatives aux CEM	9

SECTION 3 − DEFINITIONS		11
3-1.	Symbols And Definitions	11
SECTION 4 − SPECIFICATIONS		12
4-1.	Specifications For 230 VAC	12
4-2.	Specifications For 115 VAC	12
4-3. Duty Cycle And Overheating		13
4-4.	Volt-Ampere Curves	14
SECTION 5 − INSTALLATION		15
5-1.	Installing Nozzle, Contact Tip, And Adapter	15
5-2.	Installing Welding Gun	15
5-3.	Installing Work Clamp	16
5-4.	Process/Polarity Table	17
5-5.	Changing Polarity	17
5-6.	Installing Gas Supply	18
5-7.	Electrical Service Guide	19
5-8.	Extension Cord Data (Use Shortest Cord Possible)	19
5-9.	Multi−Voltage Plug (MVP) Connection	20
5-10.	Serial Number And Rating Label Location	21
5-11.	Selecting A Location And Connecting Input Power	21
5-12.	Connecting 1-Phase Input Power For 230 VAC Input	22
5-13.	Connecting 1-Phase Input Power For 115 VAC Input	23
5-14.	Installing Wire Spool And Adjusting Hub Tension	24
5-15.	Connecting Optional Spool Gun	25
5-16.	Threading Welding Wire	26
SECTION 6 − OPERATION		27
6-1.	Controls	27
6-2.	Weld Parameter Chart	28
SECTION 7 − MAINTENANCE &TROUBLESHOOTING		29
7-1.	Routine Maintenance	29
7-2.	Overload Protection	29
7-3.	Drive Motor Protection	29
7-4.	Changing Drive Roll Or Wire Inlet Guide	30
7-5.	Changing Nozzle, Contact Tip, Adapter And Liner, And Cleaning Gun Casing	31
7-6.	Replacing Switch And/Or Head Tube	32
7-7.	Troubleshooting Table	33

Image 3

Hobart Welding Products 210 MVP manual Table of Contents

Contents

File MIG Gmaw OM-249 498BProcesses Description Protect Your Investment From Hobart to You Table of Contents Warranty HOT Parts can burn Symbol UsageArc Welding Hazards Electric Shock can kill Flying Metal or Dirt can injure eyes Fumes and Gases can be hazardousARC Rays can burn eyes and skin Welding can cause fire or explosion Moving Parts can injure Welding Wire can injureFire or Explosion hazard Falling Equipment can injure About Implanted Medical Devices Principal Safety StandardsCalifornia Proposition 65 Warnings EMF Information UNE Décharge Électrique peut entraîner la mort Symboles utilisés LES Pièces Chaudes peuvent provoquer des brûlures LES Fumées ET LES GAZ peuvent être dangereuxLE Soudage peut provoquer un incendie ou une explosion LA Chute DE L’ÉQUIPEMENT peut provoquer des blessures LE Bruit peut endommager l’ouïeLES Bouteilles peuvent exploser si elles sont endommagées Risque D’INCENDIE OU LE Soudage À L’ARC risque de provoquer des interférences Proposition californienne 65 AvertissementsLes Pièces Mobiles peuvent causer des blessures LES Fils DE Soudage peuvent provoquer des blessures Principales normes de sécurité Informations relatives aux CEMEn ce qui concerne les implants médicaux OM-249 498 I1eff Symbols And Definitions− Definitions I1max − Specifications Specifications For 230 VACSpecifications For 115 VAC Overheating Duty Cycle And Overheating30% duty cycle at 150 amps Minutes Welding 20% duty cycle at 90 amps Minutes Welding Voltage Amperage Volt-Ampere Curves − Installation Installing Nozzle, Contact Tip, And AdapterInstalling Welding Gun Installing Work Clamp Turn off welding power source Process/Polarity TableChanging Polarity Installing Gas Supply After flow is set, close pressure assemblyTools Needed 1-1/8 Extension Cord Data Use Shortest Cord Possible Electrical Service Guide Multi−Voltage Plug MVP Connection Serial Number And Rating Label Location Selecting a Location And Connecting Input PowerDo not move or operate Unit where it could tip Do Not modify or rewire receptacle Connection Yellow InstallationLocal Codes − have only Qualified Persons Make Connecting 1-Phase Input Power For 115 VAC Input Installing 8 in mm Wire Spool Installing Wire Spool And Adjusting Hub Tension Connecting Optional Spool Gun Wire Feed Speed ControlExposed O-rings Threading Welding Wire Controls − Operation Weld Parameter Chart Drive Motor Protection − Maintenance &TROUBLESHOOTINGRoutine Maintenance Overload Protection Stamped Changing Drive Roll Or Wire Inlet Guide023/.025 030/.035 Groove Knurled Smooth Nozzle Contact Tip Tip Adapter Head Tube Remove nozzle, contact tip, and adapter Blow out gun casingStickout Tools Needed Mm, 10 mm Replacing Switch And/Or Head Tube Trouble Remedy Troubleshooting Table Circuit Diagram − Electrical Diagram 249 315-A Gun Workpiece Work Clamp Regulator Flowmeter Shielding Gas Wire Feeder Power Source− MIG Welding Gmaw Guidelines Typical MIG Process Connections Typical MIG Process Control Settings Wire Size Amperage RangeSelect Voltage Groove Welds Holding And Positioning Welding Gun Short Normal Long Conditions That Affect Weld Bead ShapePush Perpendicular Drag Poor Weld Bead Characteristics Good Weld Bead CharacteristicsGun Movement During Welding Possible Causes Corrective Actions Troubleshooting − Excessive SpatterTroubleshooting − Porosity Troubleshooting − Excessive Penetration Troubleshooting − Lack Of Penetration Troubleshooting − Incomplete FusionTroubleshooting − Burn-Through Direction Troubleshooting − Waviness Of BeadTroubleshooting − Distortion Base metal to move Troubleshooting Guide For Semiautomatic Welding Equipment Common MIG Shielding GasesApplication Drive rolls if necessary Welding arc not stable Wire slipping in drive rollsReadjust welding parameters Welding power source − Parts List 57 5849 32 Dia Part Description Quantity Optional 245 H100S4-10 Gun Optional Drive Rolls OptionsConsumables Service SupportAssistance Hobart Welding Products Contact your Distributor for