Hoshizaki FS-1022MLH-C manual

6)Make sure the "GM" LED is on. There is a delay of at least 30 seconds before the "GM" LED turns on after power‑up. After the "GM" LED turns on, press the "SERVICE" button located on CB to bypass the 5-minute ice purge cycle. WARNING! Risk of electric shock. Care should be taken not to touch live terminals. The "COMP" LED turns on.

7)Press the actuator paddle located in the top of the chute.

S1 dip switch 7 in the "ON" position: Comp and GM de‑energizes within 10 seconds

and CB sounds a 9‑beep alarm. S1 dip switch 7 in the "OFF" position: Comp and

GM de‑energize within 10 seconds. Diagnosis: If MBC does not open or the icemaker continues to make ice, check that the actuator paddle is moving freely. Confirm that the actuator paddle is engaged. Check for continuity across MBC wires. If MBC contacts are found open and the icemaker continues to make ice, CB is bad and must be replaced. If MBC is closed with the actuator paddle engaged, MBC is bad and must be replaced.

8)Move the power switch to the "OFF" position, then unplug the unit from the electrical outlet.

9)Replace the chute assembly and strap in their correct positions.

10)Replace the control box cover and top panel in their correct positions.

11)Plug the unit into the electrical outlet.

12)Move the power switch to the "ON" position to start the automatic icemaking process.

13)Replace the front panel in its correct position.

Legend: CB–control board; Comp–compressor; GM–gear motor; IS–infrared sensor; MBC–mechanical backup bin control

35

Image 35

Hoshizaki FS-1022MLH-C service manual

Contents

SRC-10H Hoshizaki AMERICA, INC Contents Page Unit Important Safety InformationSerious injury Indicates important information about the use and care For SRC FS-1022MLH-C Specifications Icemaker SRC-10H Condensing Unit Icemaker FS-1022MLH-C II. General Information Construction Condensing Unit a SRC-10H Icemaking Unit Sequence Cycles and Shutdown Sequence of Operation Drain Cycle Shutdown Cycle Sequence Flow Chart Control Board Sequence Flow Chart FS-1022MLH-C/SRC-10H Control Board Control Board Control Board Layout Energized Components Min Max LED Lights and Audible Alarm SafetiesNo. of Beeps Type of Alarm Reset Options Every 5 sec Sequence Step Seconds 1.6 minutes Factory Default Controls and AdjustmentsS1 Dip Switch Setting Infrared Sensor Shutdown Delay S1 Dip Switch Setting Dispense Time S1 Dip Switch Setting Drain Timer Interval Bin Control S1 Dip Switch MechanicalBackup Shutdown Delay III Wiring Diagrams High-Pressure Switch Control Low-Pressure SwitchSafety Low-Pressure Switch Manual Reset FS-1022MLH-C with SRC-10H Performance Data Ice Production Check IV. Service DiagnosisDiagnostic Procedure Page Page Page Control Board Check 5VDC Page Infrared Sensor Check Bin Control Check Mechanical Backup Bin Control Check Page Float Switch Cleaning Float Switch Check and CleaningFloat Switch Check Page No Ice Production Possible Cause Startup Diagnostic ChartsNo Ice Production No Ice Production Possible Cause Shutdown Service for Refrigerant Lines Removal and Replacement of Components Evacuation and Recharge R-404A Refrigerant RecoveryBrazing Component Important Notes for Component ReplacementEvaporator Assembly Components. See Fig Evaporator Assembly Upper Bearing Wear Check Removal and Replacement of Cutter Removal and Replacement of Auger Removal and Replacement of Extruding Head Removal and Replacement of Evaporator Page Removal and Replacement of Gear Motor 6b. Lower HousingPage Cleaning Procedure VI. Cleaning and MaintenanceCleaning and Sanitizing Instructions Cleaning Solution Float Switch Assembly Reservoir Cover Sanitizing Procedure Initial Sanitizing Solution Sanitizing Procedure Final Maintenance Frequency Area Task Maintenance Schedule Drain the evaporator Preparing the Icemaker for Long StorageRemove the water from the icemaker water supply line