Connecting the Diskette Drive Cable | HP m300 guide

13.If a diskette drive is being installed, connect the diskette drive cable to the diskette drive connector (Figure 5-19).

Figure 5-19.Connecting the Diskette Drive Cable

Removal and Replacement Procedures

5-19

Image 49

HP m300 manual Connecting the Diskette Drive Cable

Contents

Compaq ArmadaStation EM Maintenance and Service Guide Contents Appendix Symbols Using this GuideTechnician Notes Locating Additional Information Serial Number Product Description ArmadaStation EM Features External Connectors Security Features ArmadaStation EM Front Components ArmadaStation EM ComponentsDescription Function ArmadaStation EM Right Side Components Volume control switch ArmadaStation EM Rear Panel Components ArmadaStation EM Rear Panel Components MultiBays Activity LightsMultiBay/Device Compatibility Device Security Lock Half-Height BayPCI Expansion Boards Before Replacing Parts Troubleshooting Solving Docking and Undocking Problems Problems and SolutionsSolving Expansion Board Problems Problem Probable Cause Recommended Actions Solving External Mouse Problems Solving External Keyboard ProblemsSolving Expansion Device Installation Problems Press any key or click the mouse Solving External Monitor Problems Serial Number Location Illustrated Parts Catalog Compaq ArmadaStation EM Components Compaq ArmadaStation EM Components Description Spare Parts Compaq ArmadaStation EM Components Plastics Kit Components Spare Part Number Plastics Kit ComponentsItem Description MultiBay Option Cable Kit Components Spare Part Number MultiBay Option Cable Kit Spare Parts Miscellaneous not illustrated MiscellaneousSpare Part Number Electrostatic Discharge Removal and Replacement Preliminaries Preventing Electrostatic Damage to Equipment Generating StaticTypical Electrostatic Voltages Relative Humidity Event 10% 40% 55% Grounding Methods Preventing Damage to DrivesStatic Shielding Protection Levels Method Grounding Equipment Grounding Workstations Recommended Materials and Equipment Tool and Software Requirements Service ConsiderationsScrews Plastic Parts Cables and Connectors Removal and Replacement Procedures Expansion Base Disassembly Sequence Disassembly Sequence Chart Disconnecting the Expansion Base Preparing the Expansion Base for Disassembly Expansion Base Feet External Components Removing the Tray Tray Removing the Connector Cover Connector Cover Removing the Rear Bezel Rear Bezel Sliding the Manual Release Lever Locating the Expansion Slots PCI Expansion Boards 10.Removing the Expansion Slot Cover 11.Installing an Expansion Board 12.Removing the Top Cover Screws Top Cover Swing the top cover up and forward to remove it Figure Half-Height Bay Installing a Half-Height Drive 15.Removing the Half-Height Bay Blank Bezel Cover 16.Removing the Half-Height Drive Screws 17.Attaching the Bezel Cage to the Half-Height Drive 18.Connecting the Power Cable 19.Connecting the Diskette Drive Cable 20.Connecting the Hard Drive Cable 21.Connecting the CD-ROM Drive/Audio Cable 22.Installing a Half-Height Drive 23.Removing the Left Speaker Left Speaker MultiBay 24.Disconnecting the Half-Height Bay and Left Speaker Cables 25.Removing the MultiBay and Control Panel 26.Removing the Control Panel Control Panel Mechanism Assembly 28.Removing the Mechanism Assembly Power Supply 30.Removing the Power Supply 31.Removing the Backplane Backplane Pecifications Expansion Base Physical and Environmental SpecificationsMetric 2Specifications Table A-1 Headphone Jack Connector PIN AssignmentsTable A-2 Microphone Jack Table A-3 Table A-5 Serial ConnectorTable A-4 Table A-7 Stereo Line-out Jack Table A-6Table A-8 Stereo Line-in Jack Signal Pin Table A-13 Docking Connector PDATA6 LD14 Pin Signal Conductor Power Cord Set Power Cord SET RequirementsGeneral Requirements Country-Specific Requirements Conductor Power Cord Set Requirements-By CountryCountry Accredited Agency Applicable Note Numbers Index PCI Index